Pizza Cutter Size List & Appreciation Thread

[jadmt]

I have joined the M/T baja boss A/T life as well. I really like them so far. They drive great and are 100x better then the factory 2/3 worn out firestone destination M/T. Rubicon take of lift and fenders pair really well with them. Lots of talk from the techs how I chose the wrong tire and should have went 12.5. Hopefully will be getting them in the dirt soon.

They are great tires..if you want at little better stance you can do BORA 1" spacers..I use them when I am running those on stock wheels..

Sponsored

 

[Derrick20JL]

That looks so good with the Rubi fenders! Did you do just fronts? Or rears also? What size tire did you end up getting?

I did both the front and the rears. I dont have the right bumper to make them match up so it looks a little weird in the rear, but it'll look fine once I get an aftermarket rear bumper.

 

[Derrick20JL]

They are great tires..if you want at little better stance you can do BORA 1" spacers..I use them when I am running those on stock wheels..

Im thinking about doing spacers just to get them out to the edge of the fenders. Just a little un-eased with the idea of wheeling with spacers.

 

[jadmt]

Im thinking about doing spacers just to get them out to the edge of the fenders. Just a little un-eased with the idea of wheeling with spacers.

I have wheeled for years with spacers and never had an issue....1" are the lowest you can go without trimming your studs..and put the tires just at the edges..

 

[Derrick20JL]

I have wheeled for years with spacers and never had an issue....1" are the lowest you can go without trimming your studs..and put the tires just at the edges..

That does look a lot better. Its good to know that there is no trimming of studs with a 1 inch. Yeah and I dont treat it like a rock bouncer or anything so Im sure it would be fine. After seeing your set up I'll look at them a lot harder.

 

[turboaaron]

2021 willys no lift. Falken wildpeak at4 255/80/17.

So far so good . No issues. Nice on road ride improvement over factory mud terrains.

 

[CapeArt]

2021 willys no lift. Falken wildpeak at4 255/80/17.

So far so good . No issues. Nice on road ride improvement over factory mud terrains.

What is the hwy tire noise like?

 

[turboaaron]

Zero noise so far . I was concerned about the heavier tire and the e load range, but
These tires make it feel brand new. Running 37 psi .

 

[azwjowner]

Has anyone else noticed that Toyo has just added 35x10.5r17 in C load in the RT Trail?!

https://www.toyotires.com/product/open-country-rt-trail/

Only 56 pounds. I think I found my next tire!

 

[Odyssey USA]

Has anyone else noticed that Toyo has just added 35x10.5r17 in C load in the RT Trail?!

https://www.toyotires.com/product/open-country-rt-trail/

Only 56 pounds. I think I found my next tire!

C? Nice. My D load 35x10.5 Kenda Klever RT is 63 lbs if I recall correctly. Decent weight savings there.

 

[dav;d aka Claus]

Has anyone else noticed that Toyo has just added 35x10.5r17 in C load in the RT Trail?!

https://www.toyotires.com/product/open-country-rt-trail/

Only 56 pounds. I think I found my next tire!

Unfortunately my Toyo Open Country A/T III, (34X10.50R17LT D) tires are only 6,200 miles old.

If I and the Wrangler last long enough these will probably be next.

 

[Gangplank]

The recent pizza cutter post motivated me to start this thread so that all of us "pizza cutter" tire lovers can have information and photos on available sizes all in one place. Below are some popular pizza cutter tire sizes, and links to JLs with photos (where available). I've also listed some of the available tires in the less well-known sizes. If anyone has any additional photos or information to add, let me know and I'll update this post.

235/80/R17 (31.8" x 9.3")

• Photos
  • 4-door JL on 235/80R17
  • 2-door JK on 235/80R17
• Tires
  • Many choices available, all load range E
  • https://www.discounttire.com/fitmentresult/tires/size/235-80-17
  • https://www.tirerack.com/tires/TireSearchResults.jsp?width=235/&ratio=80&diameter=17

33x10.5R17 (32.8" x 10.5")

• Photos
  • Gladiator on Kenda Klever R/T in 33x10.5R17
• Tires
  • Kenda Klever R/T, Load Range D

255/80R17 (33.1" x 10.0")

• Photos:
  • 2-door JL on 255/80R17 Yokohama G003 M/T
• Tires (all load range E)
  • BFG KM2
  • Cooper Discoverer ST Maxx
  • Falken Wildpeak A/T3W
  • Hankook Dynapro XT
  • Nitto Recon Grappler A/T
  • Nitto Ridge Grappler
  • Toyo Open Country A/T III
  • Toyo Open Country R/T Trail
  • Toyo Open Country R/T
  • Yokohama Geolander M/T G003
  • https://www.discounttire.com/fitmentresult/tires/size/255-80-17
  • https://www.tirerack.com/tires/TireSearchResults.jsp?width=255/&ratio=80&diameter=17

34x10.5R17 (33.5" x 10.5")

• Photos:
  • 4-door JL on 34x10.5R17 KO2s
  • 4-door JL on Toyo Open Country A/T III
  • 2-door JK on 34x10.5R17 KO2s
  • JLU on 34x10.5R17 Toyo Open Country A/T III
• Tires:
  • BFG KO2 A/T, load range D
  • Toyo Open Country A/T III, load range D
  • https://www.discounttire.com/fitmentresult/tires/size/34-10.5-17
  • https://www.tirerack.com/tires/TireSearchResults.jsp?width=34X&ratio=10.5&diameter=17

255/85R17 (34.5" x 10")

• Photos:
  • JL on 255/85R17 Baja Boss A/T
  • JLU on 255/85R17 Baja Boss A/T (more photos, and more)
  • JKU on 255/85R17 Baja Boss A/T
• Tires:
  • Mickey Thompson Baja Boss A/T (load range E)

35x10.5R17 (34.5" x 10.5")

• Photos:
  • 2-door JL on 35x10.5R17 Kenda Klever R/T (example 1), (example 2)
  • 4-door JLU on 35x10.5R17 Kenda Klever R/T (example 1), (example 2)
  • 4-door JLU on 35x10.5R17 Interco Super Swamper SSR
  • Kenda Klever 35x10.5R17 thread on Gladiator forums
• Tires:
  • Kenda Klever R/T, load range D
  • Interco Super Swamper SSR (SSR-42R), load range E

37x11.5R17 (36.5" x 11.5")

• Photos:
  • JLU on Nitto Recon Grappler A/T, load range D
• Tires:
  • Nitto Recon Grappler A/T, load range D

37x11.5R18 (36.5" x 11.5")

• Tires:
  • Nitto Ridge Grappler, load range D

Wheels

All the sizes should work fine on stock wheels but there are wheels that are narrower than the 7.5" wide stock JL wheels. Other Mopar products, such as the Dodge Journey of certain years, had narrow wheels that match the JL hub bore of 71.5mm and the 5x127 bolt pattern. Here are some options:

• 17x6.5" Vision SW60 steel wheels, hubcentric, +40mm offset
• 17x6.5" OEM alloy wheels from a Dodge Journey (1EK85PAKAC), hubcentric, +40mm offset
• 17x7" RTX X47127 steel wheels, hubcentric, +40mm offset (also available through Discount Tire)
• 16x7" Mopar JK steel "Lux" wheels, hubcentric, +12mm offset (should barely clear the brakes based on reports of 4.5" backspacing being sufficient for 16" wheels, but untested. The natural size to run would be 255/85R16.)

Another pizza cutter to add to the list is the Nitto Recon Grappler 35 x 11.5. I have them on my 2021 JLU Willys with Mopar Lift on the stock wheels.

im thinking I can probably fit 37 x 11.5 Recon Grapplers next time

 

[Aonarch]

Has anyone else noticed that Toyo has just added 35x10.5r17 in C load in the RT Trail?!

https://www.toyotires.com/product/open-country-rt-trail/

Only 56 pounds. I think I found my next tire!

Ohhhhhhhhhh niceeee

I wonder if it is made in the USA? Tennessee or Georgia AFAIK.

 

[Gangplank]

I wonder why no 35x11.5. They make it in the R/T Pro and ATII

https://www.toyotires.com/tire-finder/size/35-11.5-r17/

 

[roaniecowpony]

Just to keep this thread current, Toyo RT Pro now lists a 38x11.50R17. That's gotta qualify as "pizza cutter if the current list in the first post has 37x11.50R17.

Sponsored