OEM LED headlights

[JLEEPER]

for anyone without the factory LED headlights, there are other options. We just installed set of our aftermarket LED headlights. They require our adapter rings, but they line up great. They are a little smaller in diameter to the OEM version, but our adapter rings feature a nice rubber ring to fill in some of the gap. These DOT approved headlights have excellent beam pattern and no flickering, all plug and play to factory connector using our adapter. The halo will turn on as soon the lights are turned on, or using the included 'trigger wire', the halo can be wired separately to parking lights(or anywhere)

Sponsored

 

[nag22]

Is the middle part projector for low beam and then it uses the reflector part for high beam?

Can you throw HID bulbs into this without blinding oncoming traffic from the "no cutoff" problem?

I honestly have no idea

 

[steffen707]

for anyone without the factory LED headlights, there are other options. We just installed set of our aftermarket LED headlights. They require our adapter rings, but they line up great. They are a little smaller in diameter to the OEM version, but our adapter rings feature a nice rubber ring to fill in some of the gap. These DOT approved headlights have excellent beam pattern and no flickering, all plug and play to factory connector using our adapter. The halo will turn on as soon the lights are turned on, or using the included 'trigger wire', the halo can be wired separately to parking lights(or anywhere)

are the middles of the lights projector and the top and bottom reflector?

 

[JLEEPER]

yes, the middles are LED projectors, very bright with a nice DOT cutoff line. Tops and bottoms are reflectors. 3000lumen low beam, 6000 high beam. Total power 60w

 

[steffen707]

yes, the middles are LED projectors, very bright with a nice DOT cutoff line. Tops and bottoms are reflectors. 3000lumen low beam, 6000 high beam. Total power 60w

Are there separate led bulbs for the high and low beam, or is it a single bulb?

 

[JLEEPER]

they are all separate.

 

[steffen707]

they are all separate.

are the high and low beam "bulbs" replaceable, or is this a single sealed unit?

 

[JLEEPER]

these are all sealed units. Have a 2yr warranty if any defects we would just replace the light

 

[weeitsmikelee]

These are kinda cool. How much for just headlight(s)? In case I order for the bike

 

[Mickgolf00]

*UPDATE*. Ran into a little delay. The original idea of using the first fuse adapter was a bust. It's too big to go into the JL fuse box spare slots. I found a company that pre wires fuses. Gonna HAVE to go with that one. Other than that. Everything is ready to go. Just gonna wait on that to come in the mail. I'll keep you folks posted...

Just curious. When you're wiring these in, do you run both lights into (1) fuse (ie..cigarette lighter) or will you run to two separate fuses? I may have missed that in this thread but wanted to confirm with someone that's done it. Finished pictures would be nice if you/anyone has them. Appreciate it!

 

[dcdanny]

So you just took an oem LED housing, and put beamtech LED bulbs into them off of Amazon? Do you have that "the snow won't melt" problem?

Nope. They're OEM. Take offs from another JL

 

[dcdanny]

Just curious. When you're wiring these in, do you run both lights into (1) fuse (ie..cigarette lighter) or will you run to two separate fuses? I may have missed that in this thread but wanted to confirm with someone that's done it. Finished pictures would be nice if you/anyone has them. Appreciate it!

Both into 1. So ultimately you'll be splicing 3 wires together. One from each light & the fuse wire. Which is (pic posted). Then into the cigarette fuse slot

 

[Mickgolf00]

Another successful upgrade thanks to the folks contributing to this thread. I want to especially thank @EgGreg. I ordered his harness and wired it up. Flashed my Jeep with the JL TazerMini. Everything worked as advertised.

 

[dcdanny]

Another successful upgrade thanks to the folks contributing to this thread. I want to especially thank @EgGreg. I ordered his harness and wired it up. Flashed my Jeep with the JL TazerMini. Everything worked as advertised.

Badass!!!!!

 

[steffen707]

Nope. They're OEM. Take offs from another JL

are the OEM units sealed? or can you replace the LED bulbs?

Sponsored