2 Door Mojito Rubi

[TankCustomsAlex]

Added some @pixeldecals fender vent stickers.

Sponsored

 

[Carlton]

We have a @Rough Country Suspensions 2.5" kit coming with front trackbar and rear trackbar bracket that should hold us over for the time being
Here's a cool picture @TankCustomsAlex edited

@TTEChris I know you had the RC track bar on your jeep and installed it on this jeep. Does it wiggle?

I installed it on my jeep, and I can wiggle it quit a bit with my hand. Seems the sleeve is not strong enough or maybe not enough thread is within the sleeve. Not quite sure.

I had the RC trackbar on a JK and it felt solid/no wiggle.

 

[TTEChris]

@TTEChris I know you had the RC track bar on your jeep and installed it on this jeep. Does it wiggle?

I installed it on my jeep, and I can wiggle it quit a bit with my hand. Seems the sleeve is not strong enough or maybe not enough thread is within the sleeve. Not quite sure.

I had the RC trackbar on a JK and it felt solid/no wiggle.

No movement/wiggle on all the RC trackbars I have installed for the JL(More than 5 now). I wish I had an answer for you, but it would probably be one of those things I need to see to determine what is causing it

Wish you were closer....

 

[Carlton]

No movement/wiggle on all the RC trackbars I have installed for the JL(More than 5 now). I wish I had an answer for you, but it would probably be one of those things I need to see to determine what is causing it

Wish you were closer....

That's why I went with the RC. It was super solid on the JK. I checked torque and it was fine as well.

Here is a video of the wiggle:

 

[TTEChris]

That's why I went with the RC. It was super solid on the JK. I checked torque and it was fine as well.

Here is a video of the wiggle:

That almost looks like the clamp is loose, or the threads are worn down inside not allowing it to clamp securely?
I would rotate the clamps around so that the open end of the adjuster and the clamps are on the same side(If that makes sense)

 

[Carlton]

That almost looks like the clamp is loose, or the threads are worn down inside not allowing it to clamp securely?
I would rotate the clamps around so that the open end of the adjuster and the clamps are on the same side(If that makes sense)

I was thinking it seemed like that as well.

I will give it a whirl and see what happens. Thanks for the advice.

 

[TankCustomsAlex]

Bullet antenna just in case I run out of ammo

 

[TankCustomsAlex]

look what arrived today. @ROAM Coilovers. Will be installed in the next few days. Pics and review coming soon

 

[TankCustomsAlex]

Installed rear @ROAM coilover & short arms kit

 

[TankCustomsAlex]

Installed the @DynoMax Exhaust Muffler Elimination Pipe - sounds awesome! Here is a sound clip. For $100 it's a must mod in my book! Anyone want any other sound clips ill be happy to record and provide. Inside the car sounds good, no drone. It sounds great IMO.

 

[TTEChris]

Finally got around to finishing up the front of Alex's 2dr.

@ROAM offroad coilover kit, and front long arms installed. The factory gas tank on the 2dr goes under the crossmember so unfortunately until they come out with a upgraded tank we will have to deal with a slight loss of ground clearance. Maybe we should just go up another 2" and throw on some bigger tires to make up for it (@TankCustomsAlex )

 

[TTEChris]

We finished installing the rear of @TankCustomsAlex long arm kit. Ride quality is a night/day improvement over the short arms that came off!

 

[TankCustomsAlex]

Having posted in a bit. Working on some mods, will have a full update by next week.

 

[TTEChris]

Installed some 14" Travel coilovers, and a @Quake LED fender chop kit . We need to order some softer springs to improve the ride and drop it down a bit as it currently dwarfs our Gladiator.

 

[TankCustomsAlex]

Added Fox ATS

Sponsored