Show us your CUSTOM MODS!!

[Titan2727]

Here is another mod

I installed a Baja design rock light to the back window. I grabbed the power from the cigarette lighter plug. The amount of light is perfect

That is a great idea!!!! Doing that next!!! Thanks for sharing!!!

Sponsored

 

[James]

This mod is for CB, uhf and vhf radios
I installed the handsets in the center console. The holes I used rubber grommets, the screws for the velcro and mic clips were cut down as to not puncture out the other side of the console.
The antenna mount I made out of a bracket.
I mounted the brain for the uhf, vhf radio to the bottom of the driver seat so if the inside floods from water it will be up and off the floor. The external speaker is held in place with double sided tape on top and bottom of the speaker.
Everything was installed with the mindset of out of sight yet easy to use

 

[James]

This was not that big of a mod just an ideal for others on running their wires for lights.

This is the gobi roof rack. I ran all of the wires inside of the tubes. Pain in the a@@!
All of the wire were over gauged so their would not be a loss of voltage to the lights.
I drilled a good size hole in the upper passenger side bracket. Filed it out to get ride of any burs that could cut the wire. Ran inside of the tube, drilled a hole in the side fender cover and put a rubber grommet in place. Silaconed the wires in the hole and installed a platice cover for a little extra protection. I have the factory auxiliary lighting kit already installed. The front lights have three power wires that need their own source of power. I had to add two relays for two of the wires.
I added rear side rock lights for a little extra light that was not over powering

Let me know if you guys have any questions

 

[Titan2727]

This was not that big of a mod just an ideal for others on running their wires for lights.

This is the gobi roof rack. I ran all of the wires inside of the tubes. Pain in the a@@!
All of the wire were over gauged so their would not be a loss of voltage to the lights.
I drilled a good size hole in the upper passenger side bracket. Filed it out to get ride of any burs that could cut the wire. Ran inside of the tube, drilled a hole in the side fender cover and put a rubber grommet in place. Silaconed the wires in the hole and installed a platice cover for a little extra protection. I have the factory auxiliary lighting kit already installed. The front lights have three power wires that need their own source of power. I had to add two relays for two of the wires.
I added rear side rock lights for a little extra light that was not over powering

Let me know if you guys have any questions

Size tires you have?

You put spacers on or is that mopar rim only, they stick out pretty far if no spacer looks good.

Overall looks really good nice job

 

[FLAFIRE]

Where do we begin??

View attachment 99018

 

[James]

Size tires you have?

You put spacers on or is that mopar rim only, they stick out pretty far if no spacer looks good.

Overall looks really good nice job

Hey
The tires are 35”
No spacers needed with the mopar wheels, this was one of the reason I went with them

 

[Titan2727]

Hey
The tires are 35”
No spacers needed with the mopar wheels, this was one of the reason I went with them

Cool...I got the other mopar wheels..all black ones. Installing tomorrow. You have mopar 2" lift as well? If so, I CANT WAIT to have mine installed on 24th cuz your looks awesome!!

 

[James]

Cool...I got the other mopar wheels..all black ones. Installing tomorrow. You have mopar 2" lift as well? If so, I CANT WAIT to have mine installed on 24th cuz your looks awesome!!

Hey

Yes, the Mopar 2” lift
I have the true beadlocking ring installed and had them powder coated.
Your going to love the lift, if you do go with the locking rings you’ll need to re-tighten them a few times after a few trips. This way they seat correctly or you’ll have leaks and come out to a flat tire.
Also I run my tire pressure at 42psi to get better mpg, we did a test and it was a massive difference between 36psi to 42 psi

 

[Titan2727]

Hey

Yes, the Mopar 2” lift
I have the true beadlocking ring installed and had them powder coated.
Your going to love the lift, if you do go with the locking rings you’ll need to re-tighten them a few times after a few trips. This way they seat correctly or you’ll have leaks and come out to a flat tire.
Also I run my tire pressure at 42psi to get better mpg, we did a test and it was a massive difference between 36psi to 42 psi

OH HECK YEAH!! Looks sick!!! I cant wait!!

Anymore pics of front view? Those bead locks are 8.5 wide right?

Thanks for sharing...looks really good!

 

[James]

OH HECK YEAH!! Looks sick!!! I cant wait!!

Anymore pics of front view? Those bead locks are 8.5 wide right?

Thanks for sharing...looks really good!

Here are a few
The Mopar are perfect fit
I added a few with my Ikamper RTT

 

[Titan2727]

Here are a few
The Mopar are perfect fit
I added a few with my Ikamper RTT

Wow everything on your rig looks perfect really good job putting it all together.

Thanks...made my day with the pictures cant wait!

 

[Titan2727]

I think these decals are pretty cool if you have these rims...

 

[Pic18]

I think these decals are pretty cool if you have these rims...

Reminds me of Darth Maul.

 

[blessidsoul12]

I think these decals are pretty cool if you have these rims...

I am getting these. $79.99 actually seems reasonable but it'll be interesting to see how durable they are...

 

[BajaDesigns]

Here is another mod

I installed a Baja design rock light to the back window. I grabbed the power from the cigarette lighter plug. The amount of light is perfect

Nice job!

Baja Designs
www.bajadesigns.com

Sponsored