ym0bc1
Well-Known Member
- Joined
- May 24, 2023
- Threads
- 71
- Messages
- 421
- Reaction score
- 278
- Location
- San Francisco Bay Area
- Vehicle(s)
- JLUR
get an extension cable. Only bleed once.
Sponsored
Sponsored
ym0bc1
Well-Known Member
- Joined
- May 24, 2023
- Threads
- 71
- Messages
- 421
- Reaction score
- 278
- Location
- San Francisco Bay Area
- Vehicle(s)
- JLUR
did Jeep change the location for the newer model year?
on my 2021, it was behind the knee speaker pod, and I yank it off when I replacing the speaker, and put the sgw on a lower position.
on my 2021, it was behind the knee speaker pod, and I yank it off when I replacing the speaker, and put the sgw on a lower position.
YGBSM392
Well-Known Member
- First Name
- Kevin
- Joined
- Aug 24, 2022
- Threads
- 10
- Messages
- 1,031
- Reaction score
- 2,494
- Location
- Oklahoma City
- Vehicle(s)
- 2025 Rubicon 392, 2024 2-Door Rubicon X, 2024 Mojave X
- Occupation
- I fly da plane...
Yep, 24 and later are a bitch!
YGBSM392
Well-Known Member
- First Name
- Kevin
- Joined
- Aug 24, 2022
- Threads
- 10
- Messages
- 1,031
- Reaction score
- 2,494
- Location
- Oklahoma City
- Vehicle(s)
- 2025 Rubicon 392, 2024 2-Door Rubicon X, 2024 Mojave X
- Occupation
- I fly da plane...
Yes, 2024 and later dash removal is much more difficult. Even getting to some of the components is a nightmare. I don't even want to know how much shop labor time would be on replacing a knee speaker!
My SGW battle:
Here's a 2024 and later dash removal. DRC has one too but I'm a little dubious of their work.
AlgUSF
Well-Known Member
- Joined
- Mar 11, 2021
- Threads
- 37
- Messages
- 1,668
- Reaction score
- 2,841
- Location
- Melbourne, FL
- Vehicle(s)
- 2021 JLUS, 2014 Tundra, 2013 Odyssey, 2002 Civic
Nobody has shown us a pic yet of a 2024+ on this thread. The 2021 is annoying, but not terrible.
Sponsored
OP
OP
WannFly
Well-Known Member
- Thread starter
- #22
this is the best I could do. I am big and that area is very small lol. the screwdriver metal part is little over 6 inch long.
Its easier if you remove the factory harness, there is also a vent on the other side, not required to remove it, but i found it easier when removed, you can use a pick tool with your other hand to press down on the clips of the harness
Dyolfknip74
Well-Known Member
- Joined
- Mar 18, 2021
- Threads
- 37
- Messages
- 5,221
- Reaction score
- 9,014
- Location
- Ottawa, Ontario, Canada
- Vehicle(s)
- 2021 JLU Rubicon
I've done a few kill switches on 24s and up and dont remember it being that bad, granted, I may have blocked it out as I have been in like 30 different JL's for my local club.
The trim removal to get to push start doesnt come off as easy but you can still get access to the wiring for the switch.
The trim removal to get to push start doesnt come off as easy but you can still get access to the wiring for the switch.
Sponsored
Last edited:
