What did you do TO your Jeep JL today?

[jlsahara]

AEV borahs installed on 35x12.5x17 KM3s, removed end caps on bumper and shorter antenna along with the new teraflex carrier.

How’s the road noise with these?

Sponsored

 

[Crusifix]

I've installed full racing stripes and wraps on dozens of cars. I've ordered graphics from Pixeldecals.com before, and they were great. However I dont know if they switched vinyl brands or what, but whatever Walmart level vinyl they sent me to use for my fender vents was the most ill fitting unforgiving pieces of thin plasticky vinyl I've ever used in an automotive application. I got them installed, but they just looked cheap, so I pulled them off and tossed them. Very unhappy guy here that usually has a very long fuse.

 

[Rhinebeck01]

I've installed full racing stripes and wraps on dozens of cars. I've ordered graphics fro. Pixeldecals.com before, and they were great. However I dont know if they switched vinyl brands or what, but whatever Walmart level vinyl they sent me to use for my fender vents was the most ill fitting unforgiving pieces of thin as plasticky vinyl I've ever come in contact with. I will not order anything fro. Them again. $40 down the drain. I got them installed, but they just looked like cheap shit, so I pulled them off and tossed them. Very unhappy guy here that usually has a very long fuse.

@Crusifix

If chitty as you say, then @pixeldecals needs to send you better product or give you a full refund.

 

[IndustrialAction]

Got her topless and installed GPCA hardtop quick release screws and tie-downs

 

[Crusifix]

@Crusifix

If chitty as you say, then @pixeldecals needs to send you better product or give you a full refund.

Maybe I'm too picky, but for the price, I was expecting better quality vinyl. It's not worth the hassle at this point, as I doubt I would be happy with a replacement that they would send I will just get my vinyl guy to make some from his Oracal 970RA or 3M stock.

 

[Mantacon]

Maybe I'm too picky, but for the price, I was expecting better quality vinyl. It's not worth the hassle at this point, as I doubt I would be happy with a replacement that they would send I will just get my vinyl guy to make some from his Oracal 970RA or 3M stock.

Did you even reach out to @pixeldecals? He is a nice guy and responds to messages almost instantly. Im sure he would of helped you and bashing them on the forum is not the way to do it.

 

[Brian0128]

Installed Rock Hard sliders/step with my wife today. Called Jason and ordered them 2 weeks ago with the black top plate and no logo.

 

[Crusifix]

I didn't even realize they were vendors here. It just put me in a bad mood. I had already put a hood decal in my shopping cart and was getting excited about it. I was just disappointed in the vinyl. I will always give an honest opinion. Nothing should prevent that.

 

[Crusifix]

I've installed full racing stripes and wraps on dozens of cars. I've ordered graphics fro. Pixeldecals.com before, and they were great. However I dont know if they switched vinyl brands or what, but whatever Walmart level vinyl they sent me to use for my fender vents was the most ill fitting unforgiving pieces of thin plasticky vinyl I've ever used in an automotive application. I got them installed, but they just looked cheap, so I pulled them off and tossed them. Very unhappy guy here that usually has a very long fuse.

Wow, I just reread what I wrote, and it was a bit harsh and poorly written..LOL

 

[Rhinebeck01]

I didn't even realize they were vendors here. It just put me in a bad mood. I had already put a good decal in my shopping cart and was getting excited about it. I was just disappointed in the vinyl. I will always give an honest opinion. Nothing should prevent that.

@Crusifix

You did absolutely nothing wrong. If the offering is iffy, it does not matter whether the provider is a forum sponsor or not. You have every right to say something..

I tagged @pixeldecals after I saw your initial post. This will get pixeldecals attention.

Perhaps they had a poor batch of vinyl.

Anyway, if the offering is not up to snuff, then they need to make it right or give you a refund which undoubtedly they will do. They are known to be a good vendor and will work with you I'm sure.

.

 

[GreyFox]

Maybe I'm too picky, but for the price, I was expecting better quality vinyl. It's not worth the hassle at this point, as I doubt I would be happy with a replacement that they would send I will just get my vinyl guy to make some from his Oracal 970RA or 3M stock.

I did that too. I took the ones I had made to my local vinyl guy who did them in a bright green and in one solid piece, not two pieces of vinyl stuck on top of another. Plus, my local guy uses 3M and the difference in thickness and quality was quite noticeable.

 

[FrenchSSGTMike]

Got her topless and installed GPCA hardtop quick release screws and tie-downs

Love your orange theme, where did you get your jeep letters ?

 

[Goin2drt]

Wow, I just reread what I wrote, and it was a bit harsh and poorly written..LOL

No problem at all with your post. Speaking honestly is great and don’t get enough because everyone always thinks you have to hide the truth and give a company or vendor all these chances first. Get it right the first time. If you don’t then that is what forums are for to make other people aware. Also gives the company an opportunity to make it right and get the kudos for resolving an issue because they do happen.

 

[blessidsoul12]

Did I make the 1000th page!?

 

[blessidsoul12]

how 'bout now!?

Sponsored