Search results

Anybody install these aftermarket coil packs? Click to Enlarge (2 Reviews) 5 Stars Ignition Coil and Spark Plug Kit 12 Piece - 2018-2020 Jeep Wrangler 3.6L V6 - TRQ

I have a 2019 JLU Sport Manual. When I go up any slight hill in 5th I suffer a loss of power and have to down shift to 4th then the Jeep will not go above 60, (slower when up hill). I’ve change the cam shaft sensor in bank 1, oil control valves on both sides and the intake VVT on bank 1. I did...

Long Story......... I've had lots of engine issues in the past and I've always fixed them myself. I was contacted by Jeep about the clutch recall and finally Jeep is going to replace the clutches. I figured why not if it is free. I contact the dealership and set an appointment. Jeep gets...

Long Story.... I replaced my lifters/ rockers and intake camshaft on the bank 1 side about 500 miles ago. Over a year ago I replaced my clutch and broke a wire going to my neutral safety switch which caused the ESS light to come on and ever since the jeep does not know what gear it is...

Anyone know which slot the fuse for the Nuetral switch sensor is located. The cover was no help and Google didn’t get me much further. Any help is appreciated.

I've seen a couple custom jeeps with soft tops and instead of a plastic windows on the side it is just an all fabric insert. I've been looking around and cant seem to find them. Has anyone seen something like this for sale? I tried going to a place that redoes car interiors and they didn't...

I picked the new lifters for the intake side and they are visible different. Has anyone used the newer version. One on the left in the picture is the old the right one is the new. I ran with the ticking for almost 18 months now I’m paying the price. Replacing 3 of the intake rocker arms at $80...

Finally going to replace my bad rocker/lifter. We did this on my friends JKU, also 3.6L. When I went to order the rockers from mopar I found that they have lash adjusters rocker arms and valve rocker arms. The valve cost 7xs the lash and the design looks different from the ones we installed in...

Looking for the wiring diagram for a plugged that tore off while taking the bell housing down. It is located on the driver side of the bell housing. It goes from the bell housing to a connector on a bracket connected to the bell housing then transfers to a 3 prong connecter that looks like it...

This weekend after 2yrs and 40k miles The clutch has begin slipping. It has taken some major abuse and I decided with the amount of times I've smoked the clutch it probably has closer to 100k miles on it :/ Ive had the issue with not going into gear and poor shifting since last summer. I...

I have the ticking sound 3.6L/manual. It is not the type that is loud at start then slowly goes away. Its a constant ticking when the engine is running and gets louder when I accelerate. I've read that when it is at start up, it is just a bad rocker arm. If its constant do I need to replace the...

Getting ready to replace and bleed brakes. I have already heat shielded the hydraulic lines which seemed to help with shifting. I was looking at replacing the DOT3 with DOT 5.1. Everything I've read says it wont have an adverse affects on the brakes. I assume that means it will not have an...

I have already replaced my frame side bushing on my EVO track bar twice and now it appears to be loose again. It moves back and forth on the frame side about a quarter inch. The bolt is tight and does not move so I'm pretty sure the mounting bracket is not ovalled out. Has anyone seen this issue...

My spider gears are what gives!!! I've shredded my spider gears for the 3rd time. Is there something else I should be looking at that could be the cause. Not really complaining because they are cheap to replace but wanted to see if there could be an underlying issue, other than my beat'n not...

Im looking to connect my MLC-6 to the N4 terminal on the bus bar. Has anyone been connected to that terminal for a prolonged time. Dont want to leave myself stranded somewhere if damages the bar?

Looking to buy just the pinion for a Dana 30 geared in 3.73. I broke a few teeth on mine when I shattered the spider gears. Currently it hasn't had any issues with the 4x4 but its always in the back of my head when I go out. I'm figuring that most people/shops just end up throwing these out when...

Anybody install a teraflex hand throttle on the JLU yet? Looking for some pointers before I turn this 1 hour project into a half day project

Anybody install a teraflex hand throttle on the JLU yet? Looking for some pointers before I turn this 1 hour project into a half day project

Feel into a v notch twice yesterday and trying to get back out I heard a snapping/ Kachunk a couple times then 4x4 was no longer a thing. I had to be winched back and it seemed to be in 4x4 reversing down some obstacles but when I went to cut it sharp to drive out the snapping noise occurred...

I blew my side wall earlier this week and while the tire is warrantied, it will still take till the end of next week to get one shipped. I'm looking to just purchase a single used 37" tire and wheel to run as my spare this weekend. If it came on a stock wheel with no offset would it make the...