What did you do TO your Jeep JL today?

[mtnsurfer]

Took her out with some friends and got a little dirty

Sponsored

 

[iWantJLU]

Installed Diode Dynamics switchback LEDs in the fenders. Switches between white and amber when you engage the turn signal. On my Sport S I now have OEM LED fogs that came with my JLUR take off steel bumper, OEM LED headlights - takeoffs - currently no halo, and DD LED switchbacks in the fender.

Looks great, will you be able to enable the halo feature on the oem headlights?

 

[Blu bi Kong]

Very smart use of that. How did you attach it?

Two sided 3m sheets. Works amazing

 

[dragonslayer]

Where did you get the Jeep canteen?

dealer NOS stock, about $25 i think.

 

[pichenet]

Looks great, will you be able to enable the halo feature on the oem headlights?

Great question. I'm interested in the wiring harness that comes with the Mopar headlight set. Not sure if that will help or not. I'm also thinking of running a feed from my parking lights to the 4rth pin on the headlights.

 

[Kenny]

Picked up my Sport S yesterday so starting slow - put those rubber inserts everywhere.

Now onto putting in the gas filler door, sill guards, mats, and Harken hoist.

 

[NCSUSTATS]

Installed the black mopar door sill protectors...too bad mopar didn’t realize the sill was curved...gives a nice cheap, ill-fitting, done-in-the-auto-parts-store-parking-lot look to my 50k new truck. At least they provide minimal protection. Hopefully a better option pops up before the back edge of the guard fills up with dirt and i rip it off to clean.

...and the keyhole on the JL mopar locking gas cap I bought was too small for the JL’s key.

 

[Cody6597]

What lift are you running?

RC 2.5

 

[islandtees]

Installed the black mopar door sill protectors...too bad mopar didn’t realize the sill was curved...gives a nice cheap, ill-fitting, done-in-the-auto-parts-store-parking-lot look to my 50k new truck. At least they provide minimal protection. Hopefully a better option pops up before the back edge of the guard fills up with dirt and i rip it off to clean.

...and the keyhole on the JL mopar locking gas cap I bought was too small for the JL’s key.

I have the Mopar locking cap and you have to key it yourself.

 

[NCSUSTATS]

I have the Mopar locking cap and you have to key it yourself.

Yeah, I know...

 

[OnlyOne]

Installed the black mopar door sill protectors...too bad mopar didn’t realize the sill was curved...gives a nice cheap, ill-fitting, done-in-the-auto-parts-store-parking-lot look to my 50k new truck. At least they provide minimal protection. Hopefully a better option pops up before the back edge of the guard fills up with dirt and i rip it off to clean.

...and the keyhole on the JL mopar locking gas cap I bought was too small for the JL’s key.

I installed some 3M film. Works great. 7 bucks for a roll that will do all 4 doors and then some,on amazon.

 

[NCSUSTATS]

I installed some 3M film. Works great. 7 bucks for a roll that will do all 4 doors and then some,on amazon.

I tried installing some pre-cut pieces that I just couldn’t get fit properly...once my frustration/irritation subsides I may try a less aggressive fitment like what you did

 

[raqball]

Debaged it (well I did it yesterday)....

 

[ThirtyOne]

Picked up my Sport S yesterday so starting slow - put those rubber inserts everywhere.

Now onto putting in the gas filler door, sill guards, mats, and Harken hoist.

DO you have a link for these inserts?

 

[OnlyOne]

I tried installing some pre-cut pieces that I just couldn’t get fit properly...once my frustration/irritation subsides I may try a less aggressive fitment like what you did

Yeah it’s a lot like window tint. I found it to be a pain at first but with some patience it comes out pretty nicely. Just use lots of soap spray and keep it wet.

Sponsored