OminousSkitter
Well-Known Member
So wine? Too bad modern gas containers don't have that breather cap in the back—perfect for decanting.
Sponsored
Sponsored
WRGLR-JL
Well-Known Member
Like the idea of the cover, but the upper corner seems not to fit well. Is it me or the picture angle? If not the angle then I'm not a buyer. I'd be looking at it all the time!Not much today unfortunately:
- put the Utah Foundry covers for the back of the front bumper
- tried to hold my stop light to the mount with 3M double-side tape (somehow the two bolts that held it down went AWOL last week and the light was hanging by the wire)
Bill_BCNtoNY
Well-Known Member
you know, I thought exactly the same thing when I installed it… but worked around the Jeep for a while today and didn’t even notice (vs I used to notice the fog lamp wires and connectors all the time).
I’m happy with the covers; not perfect but good enough for me
Sponsored
Bill_BCNtoNY
Well-Known Member
I’d encourage you to get them if that corner is your only concern - you can (i) easily do a better job than me when sticking the rubber strip to the cover and probably even (ii) shape the cover to conform bette to the shape of the bumper.
Hercules
Well-Known Member
- Joined
- Jan 1, 2022
- Threads
- 9
- Messages
- 563
- Reaction score
- 1,178
- Location
- Clearwater, FL
- Vehicle(s)
- 2012 Ram 2500 Longhorn, 2022 JLURD
Bro,
I did the same thing happen to me at SMORR in the Ozarks. Slipped off a wet rock ledge into a tree wedging through a tight v notch trail. Popped out the right bottom side of the fender, scraped up the whole outside edge. Ending up going with revmoto for an oem replacement part, paint matched and delivered direct to my house. Pricy, but can’t complain.
I did the same thing happen to me at SMORR in the Ozarks. Slipped off a wet rock ledge into a tree wedging through a tight v notch trail. Popped out the right bottom side of the fender, scraped up the whole outside edge. Ending up going with revmoto for an oem replacement part, paint matched and delivered direct to my house. Pricy, but can’t complain.
jadewolf
Well-Known Member
- Joined
- Mar 7, 2021
- Threads
- 8
- Messages
- 658
- Reaction score
- 2,830
- Location
- California
- Vehicle(s)
- 2012 JK Sport (sold), 2021 JL Rubicon
- Build Thread
- Link
Dang, that's the exact lift/tire combo I've been considering for my 2dr. I think you just sold me on the Clayton 1.5. It looks fantastic! Perfect proportions!Agreed…. I have 315 KO2s on 0 offset and 1.5in Clayton lift is the sweet spot especially for 2dr.
jadewolf
Well-Known Member
- Joined
- Mar 7, 2021
- Threads
- 8
- Messages
- 658
- Reaction score
- 2,830
- Location
- California
- Vehicle(s)
- 2012 JK Sport (sold), 2021 JL Rubicon
- Build Thread
- Link
Looks great! How did your install go? My Destroyers just were just delivered yesterday for my 2 door. Hoping to get them on next week. Any issues getting them installed? Did you need to cut the skid plate down? Did you need to loosen the body bolts to get the mounts over the washer? I see a lot of install experiences of these from 4 door owners, but not much for 2 doors.Through on some LOD Destroyers. Hella stout.
Sponsored
dragoneggs
Well-Known Member
- First Name
- Mark
- Joined
- Dec 14, 2021
- Threads
- 73
- Messages
- 9,334
- Reaction score
- 40,818
- Location
- Seabeck, WA
- Vehicle(s)
- '22 Snazzberry Pearl JLR
- Build Thread
- Link
Do it
Do it! Best mod I have done. Want more pics? I should get a commission. Ha ha!
jadewolf
Well-Known Member
- Joined
- Mar 7, 2021
- Threads
- 8
- Messages
- 658
- Reaction score
- 2,830
- Location
- California
- Vehicle(s)
- 2012 JK Sport (sold), 2021 JL Rubicon
- Build Thread
- Link
Heck yeah, let's see some more pics!
dragoneggs
Well-Known Member
- First Name
- Mark
- Joined
- Dec 14, 2021
- Threads
- 73
- Messages
- 9,334
- Reaction score
- 40,818
- Location
- Seabeck, WA
- Vehicle(s)
- '22 Snazzberry Pearl JLR
- Build Thread
- Link
jadewolf
Well-Known Member
- Joined
- Mar 7, 2021
- Threads
- 8
- Messages
- 658
- Reaction score
- 2,830
- Location
- California
- Vehicle(s)
- 2012 JK Sport (sold), 2021 JL Rubicon
- Build Thread
- Link
Gorgeous! That color is ?, too! Great lookin Jeep!
jadewolf
Well-Known Member
- Joined
- Mar 7, 2021
- Threads
- 8
- Messages
- 658
- Reaction score
- 2,830
- Location
- California
- Vehicle(s)
- 2012 JK Sport (sold), 2021 JL Rubicon
- Build Thread
- Link
Finally found a spot to properly spool my new winch line under tension. In the treeless desert, there's not much to anchor on. But drove past this pile of old telephone poles on the side of the road tonight and knew it was meant to be.
This thing is a lot easier to work with than the steel cable on my old winch. Loving the synth line so far!
Also got my LOD Destroyers delivered yesterday, unpacked them today and getting ready to install them next week.
And, unlike my LOD bumper, I didn't have to excavate them like Ellie Sattler digging up a new dinosaur. The foam was mostly only around the edges this time, ha! No trowel required!
Sponsored
