Torque Specs

[20-Willys]

Hello,

Does someone have a good list of suspension torque specs without the torque plus degrees they could share here? I have a found a couple of conflicting charts mostly with the rear seeming low.

TIA

Sponsored

 

[Deleted User 38384]

I know I'm going to get a lot of hate for this, but for me, the only torque's are wrench tight and wrench very tight.

 

[chevymitchell]

Hello,

Does someone have a good list of suspension torque specs without the torque plus degrees they could share here? I have a found a couple of conflicting charts mostly with the rear seeming low.

TIA

Each flat on the bolt head or nut is 60 degrees. You can guestimate from there or get a degree adapter for your TQ wrench.

 

[20-Willys]

Yeah, because it so awkward maneuvering around under there I am hoping to find the number and just listen for the click.

 

[Terrymo]

From Mopar 2 inch lift instructions

 

[20-Willys]

I found these, but the rear control arm specs seems low at 90 where the one in degrees on this site mentions starting at 100.

SUSPENSION (FRONT)


Part |Nm |ft. lbs .| in. lbs. | Comments
Hub and bearing bolts | 102 | 75 | - |
Hub and bearing nut | 136 | 100 | - |
Lower control arm rear nut | 140 + 145° | 103 +50° | - |
Lower control arm front nut | 140 + 145° | 103 +50° | - |
Lower ball joint nut (initial torque) | 20 | 15 | - |
Lower ball joint nut (final torque) | 45 | 33 | - |
Shock absorber lower bolt | 100 | 74 | - |
Shock absorber upper bolt | 110 | 81 | - |
Stabilizer bar bolts | 63 | 46 | - |
Stabilizer bar link upper nut | 93 | 69 | - |
Stabilizer bar link lower bolt | 80 | 59 | - |
Track bar frame nut | 70 + 115° | 52 + 115° | - |
Track bar axle bolt | 70 + 115° | 52 + 115° | - |
Upper control arm front nut | 55 + 185° | 41 + 185° | - |
Upper control arm rear bolt | 50 + 135° | 37 + 135° | - |
Upper ball joint nut | 75 | 55 | - |

SUSPENSION (REAR)

Part |Nm |ft. lbs .| in. lbs. | Comments
Lower control arm front bolts | 100 + 50° | 74 + 50° | - |
Lower control arm rear nut | 100 + 50° | 74 + 50° | - |
Shock absorber upper bolt | 110 | 81 | - |
Shock absorber lower nut | 100 | 74 | - |
Stabilizer bar bolts | 63 | 46 | - |
Stabilier bar link upper nut | 90 | 66 | - |
Stabilizer bar link lower nut | 80 | 59 | - |
Track bar nut (frame end) | 100 + 30° | 74 + 30° | - |
Track bar bolt (axle end) | 100 + 60° | 74 + 60° | - |
Upper control arm front bolt | 100 + 80° | 74 + 80° | - |
Upper control arm rear nut | 100 + 65 ° | 74 + 65° | - |

 

[Terrymo]

I believe the lower chart has 3 columns per item
Newton Meters, Foot Pounds, then inch pounds (if applicable)

 

[20-Willys]

Okay, that's good news! I used the upper chart for everything but was second guessing it.

Sponsored