OEM Interior Intrusion Sensor

[Gregj]

So, got everything in and hooked up but I can’t get to the ITM module to set the ultrasonic and tilt, says I need a blue cable to get to it. Found a set of cables but they won’t get here till Thursday.

Gregj

Sponsored

 

[mciaio]

says I need a blue cable to get to it

Yup, need an vlinker mc+ or the obdlink mx+ or the blue adapter cable.

 

[richk225]

Part numbers please?? I have to look but because of JSCAN I believe I had purchased a OBDLINK MX+ Time to go on a treasure hunt in the garage

Gergj how is my harness coming along? Seriously I can't wait to see how this turns out.
My Raptor has 3 settings that you can choose from, setting it on very sensitive and leaving the windows down while down at the beach the wind will set it off

 

[Gregj]

I have an MX+ but still can’t get to it.

 

[mciaio]

I have an MX+ but still can’t get to it.

That's weird my MC+ went right in.

 

[mciaio]

FYI for people considering this. You will get false alarms with the top and doors off on gusty days. Its happened to me twice in the last couple weeks. I didn't know why the alarm was going off so I started reading the interwebs and found out ultrasonic sensors can be affected by wind. We have 15 mph gusts today, so that seems to be enough.

 

[richk225]

FYI for people considering this. You will get false alarms with the top and doors off on gusty days. Its happened to me twice in the last couple weeks. I didn't know why the alarm was going off so I started reading the interwebs and found out ultrasonic sensors can be affected by wind. We have 15 mph gusts today, so that seems to be enough.

I had mentioned that earlier, my Raptor has the same setup but it has 3 settings for sensitivity
Well while down the beach one day I learned that the increase in wind noise going through the cab will trigger the alarm. I just had to change the setting and there were no more issues.
Gregj has been doing a lot of homework on getting this to work and figuring out if the dealer has to activate the control module or if it can be done by Jscan. My 392 has the safety package and there are already 2 microphones in the assembly. Hopefully it will work out for him and I`m following his every step along with what has been written on the Trackhawk forum
Here are a few pics with the advanced safety group

 

[mciaio]

I have those mics too. Those are not the ultrasonic sensors. Those are the handsfree mics. I activated mine with jscan, no need to go to the dealer. It's all laid out in the original post. Wranglers did not come with the module, so unless you buy it and install it, nothing will work.

The round ones are the ultrasonic ones from the added module.

 

[mciaio]

 

[richk225]

A big Thank you for all of the information! I am waiting on the module 68329822AA to arrive.
I had bought an overhead center console but it is from a 2022 or 2023 and the module number is different #68566130AC but it has the sensors. It shows that it is from a Challenger or Charger or a Chrysler 300

https://www.mymoparparts.com/oem-parts/mopar-intrusion-module-sensor-68566130ac

 

[Gregj]

I think I have a bad module because the VIN’s are just ??????

I’ll have to get another one and try that.
Gregj

 

[mciaio]

I think I have a bad module because the VIN’s are just ??????

I’ll have to get another one and try that.
Gregj

I had the same issue. I wrote about that in the original post. Need to soft reset all controllers.

 

[mciaio]

I had bought an overhead center console but it is from a 2022 or 2023 and the module number is different #68566130AC

It might work. Did you try it? Does it look the same and have the same connector?

 

[Gregj]

I had the same issue. I wrote about that in the original post. Need to soft reset all controllers.

Tried that, several times along with the hard reset, still no luck.
Gregj

 

[mciaio]

OK, try this. Somewhere there is a setting for vin counter and vin limit. Set both to 0 and then do a soft reset.

Sponsored