What did you do TO your Jeep JL today?

[Geronimo]

To me , it smelled like freedom…

no more driving miss daisy, time to get out there and mat the sumbich…… wear these tires out so I can spend the rest of my savings on some 38s ……

Now that's what I'm talking about.

Fixing to hammer on it again today.

We were dodging tornadoes yesterday just west of little Rock Arkansas.

 

[Jeepless]

Was it that noticeable when you first install it? Or do you think it’s due to UV oxidation?

For how much they cost, they really should be a perfect match.

It was off from the start and my jeep only has 7000 miles. So not from wear and tear or paint defects.

 

[itsbeenfunmike]

It was off from the start and my jeep only has 7000 miles. So not from wear and tear or paint defects.

Got it. Mine doesn’t look too off, even in direct sun it can’t really tell it apart from the rest of the body color.

I’ll probably add a bit more ceramic wax to it next time I wash the Jeep.

Aside from that, I’m really enjoying them as turn signals and “puddle” lights as it’s been raining here more than normal in SoCal.

 

[Jeepless]

Got it. Mine doesn’t look too off, even in direct sun it can’t really tell it apart from the rest of the body color.

I’ll probably add a bit more ceramic wax to it next time I wash the Jeep.

Aside from that, I’m really enjoying them as turn signals and “puddle” lights as it’s been raining here more than normal in SoCal.

I saw that it’s really a hit or miss on the colors being off or not! It’s ok, I’ll get them painted, and then I think I’m going to add quick connectors in case I need to remove the cowls again. That way I won’t have to disconnect at the turn signal and aux switch again.

 

[itsbeenfunmike]

I saw that it’s really a hit or miss on the colors being off or not! It’s ok, I’ll get them painted, and then I think I’m going to add quick connectors in case I need to remove the cowls again. That way I won’t have to disconnect at the turn signal and aux switch again.

Yea, I made sure to add quick disconnects on mine. I used deutsch connectors on each one so I can still completely remove the panels if I need to.

 

[JP29]

Not today, but soon. MP Concepts aluminum copy of Rubi front and rear. Will wait to install until I get the Oracle fog light brackets and rear bumper reverse lights.

 

[Red Willy]

Found a set of Rubi fenders with LEDs for 100 bucks. A little scratched up, but no big deal.

 

[Jreycnc]

I had the dreaded DW after just 30k miles ... Sooooo, we found the cure in the form of some Dynatrac HD ball joints... What a difference they made, now it drives like it should!

I just installed teraflex hd ball joints on our 22. It had 17k miles and the stock ones were sooo loose

 

[melendez69]

I took off my Dixie horn while back, and then I waterlogged my OEM horn, so I got this guy off Amazon for $23, pretty damn loud too. A lot louder than the OEM horn that's for sure. Definitely not as loud as the Dixie horn though. I bought the horn in a cyan plated covering color, and spray painted it with some "gunmetal blue" on top,, which gave it this deeper blue color.

Then I give her a wash, and wax. It's supposed to rain today.

I never dry my Jeep, mostly because I don't really care that much about my paint job. But I find these three things give me a really good shiny clean with just one once around, and a rinse. Dirt and mud grime will just drip off. And it leaves it with a nice shiny coating even with it drip drying.

Hi, Greg. Can we be friends? I already know your first name, but I swear I'm not creepy.

 

[swampflyer]

Had gcp-1 and the no co pro genius 10x1
Charger installed. Install at Williams 4x4 professional work. Took a while to install the way I wanted. Labor is not cheap. Lol. Routed up and over frame rail fuel tank and comes out at fire wall right at fuse box. Charger Velcro mounted to top of fuse box. Basically followed wireing harnesses from other factory installed items. Installer said it was a bitch to do it this way but it’s not going anywhere. Bracket can be moved to different locations if desired. Muffler and tail pipe is lower. Sorta at same level as tow connectors. Photos are tight, I know but there’s not much room under the hood.

 

[unknownsolo]

Had gcp-1 and the no co pro genius 10x1
Charger installed. Install at Williams 4x4 professional work. Took a while to install the way I wanted. Labor is not cheap. Lol. Routed up and over frame rail fuel tank and comes out at fire wall right at fuse box. Charger Velcro mounted to top of fuse box. Basically followed wireing harnesses from other factory installed items. Installer said it was a bitch to do it this way but it’s not going anywhere. Bracket can be moved to different locations if desired. Muffler and tail pipe is lower. Sorta at same level as tow connectors. Photos are tight, I know but there’s not much room under the hood.

What is this for?

 

[TX_Ovrlnd]

Had gcp-1 and the no co pro genius 10x1
Charger installed. Install at Williams 4x4 professional work. Took a while to install the way I wanted. Labor is not cheap. Lol. Routed up and over frame rail fuel tank and comes out at fire wall right at fuse box. Charger Velcro mounted to top of fuse box. Basically followed wireing harnesses from other factory installed items. Installer said it was a bitch to do it this way but it’s not going anywhere. Bracket can be moved to different locations if desired. Muffler and tail pipe is lower. Sorta at same level as tow connectors. Photos are tight, I know but there’s not much room under the hood.

That's a very long routing of power wire, I would grab a 4xe cowl plug box and fab up something in that. Keep it short and up out of harms way.

 

[Friday2322]

I just installed teraflex hd ball joints on our 22. It had 17k miles and the stock ones were sooo loose

3 of the 4 of mine were absolutely trashed, at least on my JK I got about 60k miles before they went out.

 

[mrtm1970]

Got my Z-Automotive wire harness extension and ECRI installed to play around a little with JScan.

Also installed the under hood LED light from
Under Hood Light

Found the stock antenna again as a useful tool, lol

Removed the stock hood prop rod and Mounted the light with the tape supplied on the light:

Drilled hole bigger and used a dremmel (not shown) to clear the area for the plunger to not short out on the frame:

Pulled off the front fascia panel to install the plunger and tested the light…FYI, if you get this kit and install at the same spot, you will have the lower washer and nut at the very end of the thread (so you don’t have to figure out the right adjustment):

Works with Hood being latched down:

 

[swampflyer]

That's a very long routing of power wire, I would grab a 4xe cowl plug box and fab up something in that. Keep it short and up out of harms way.

just checked, its working fine and it came with a 12ft cord.