BCassels
Active Member
Everything was bolt on. Install wasn’t bad at all. The hardest part was breaking the factory bolts loose on the stock bumper.
Sponsored
Sponsored
Snayte
Well-Known Member
- First Name
- Nathan
- Joined
- Mar 25, 2019
- Threads
- 4
- Messages
- 444
- Reaction score
- 588
- Location
- Eau Claire, WI
- Vehicle(s)
- 2019 JL Sahara Hella Yella, 2017 Ram 1500 Longhorn
My dealer got it right! I thought there might be a better chance since they warranty the engine for life.
Az-jewel
Well-Known Member
- First Name
- Julie
- Joined
- May 1, 2019
- Threads
- 7
- Messages
- 352
- Reaction score
- 573
- Location
- Southern Utah
- Website
- aquajeepgirl.com
- Vehicle(s)
- ‘18 JLU Sport S
- Build Thread
- Link
- Occupation
- SAHM
Sure! I just went to Home Depot and picked up 4 1 ft dowels (mine has them already cut) and a roll of paracord. I drilled holes about an inch in on each end of the dowels. Then I just went out the my Jeep and kind o measured about how long it would be to tie onto the seat and loop down and back up and added some for the knots. Then I cut the cord, and started feeding it through the holes. The lowest rung has the bottom if the cord loop, and knots on top of the dowel. Then a space and knots above and below each dowel. Then I just tied it to the seat. Hope that made sense?
My little guy loves climbing up into my Jeep now!!
HomesteadRubi
Active Member
Made temporary door sill guards out of some vinyl wrap I had laying around to minimize any shoe scuffing that may occur when my little girls get in and out of the Jeep. Luckily there were no scuffs yet.
Sponsored
Hardybreed
Well-Known Member
Ha ha, must be the angle of the photo. Just a little 37".What size tire is that lol!!
Holy f**k
four low
Well-Known Member
- Joined
- Feb 1, 2017
- Threads
- 13
- Messages
- 3,106
- Reaction score
- 3,681
- Location
- central New York
- Vehicle(s)
- 2018 JL
I made a Brush Guard from a Dumpster Find, it goes into my 2" front Receiver.
Light Duty, easy on and off. Dogs like it..
Light Duty, easy on and off. Dogs like it..
- First Name
- Brett
- Joined
- Sep 14, 2018
- Threads
- 41
- Messages
- 2,430
- Reaction score
- 3,031
- Location
- Navasota, TX
- Vehicle(s)
- 2019 JLUR-8 speed 2020 F-350
- Banned
- #21,068
We’ve been working with a local company for these! They act as a security enclose when the top is off along with doubling the storage capacity. Theres also a top plate that holds a high lift jack, shovel and axe in whats basically dead space. Have about 6” of adjustability. Absolutely love these and installed one in my wife’s Jeep too. We can keep our sons baseball stuff and still have plenty of room for groceries or anything else.
My buddy that designed this weights about 200 lbs and was laying in it without any deflection.
Brett
My buddy that designed this weights about 200 lbs and was laying in it without any deflection.
Brett
CallMeJay
New Member
- First Name
- Jay
- Joined
- Sep 30, 2019
- Threads
- 0
- Messages
- 2
- Reaction score
- 14
- Location
- North Carolina
- Vehicle(s)
- 2019 Wrangler Unlimited Sport
Installed my new Rock Hard 4x4 Patriot rocker guards last night and grabbed a pic this morning before work. First real upgrade since getting my new JLU a few weeks ago. Also my first post!
Stormin’ Moorman
Well-Known Member
Pretty nice. When are y’all going to be marketing these?We’ve been working with a local company for these! They act as a security enclose when the top is off along with doubling the storage capacity. Theres also a top plate that holds a high lift jack, shovel and axe in whats basically dead space. Have about 6” of adjustability. Absolutely love these and installed one in my wife’s Jeep too. We can keep our sons baseball stuff and still have plenty of room for groceries or anything else.
My buddy that designed this weights about 200 lbs and was laying in it without any deflection.
Brett
Sponsored
- First Name
- Brett
- Joined
- Sep 14, 2018
- Threads
- 41
- Messages
- 2,430
- Reaction score
- 3,031
- Location
- Navasota, TX
- Vehicle(s)
- 2019 JLUR-8 speed 2020 F-350
- Banned
- #21,071
We’re shooting for taking these to marktet in 60 days max. These were all built in house on his plasma table but he’s wanting to have them cut on the laser or water jet to make sure the tolerances stay where they are at. I’ve seen several of these racks out there and this is by far my favorite and are stout
Brett
JSFoster75
Well-Known Member
- First Name
- Scott
- Joined
- Oct 6, 2019
- Threads
- 145
- Messages
- 2,542
- Reaction score
- 2,751
- Location
- Bluff City, TN
- Vehicle(s)
- 2019 JLUR (Mojito), 2022 JLR (Tuscadero)
- Vehicle Showcase
- 4
Been adding pink accent decals and things to my wife’s Jeep lately.
JSFoster75
Well-Known Member
- First Name
- Scott
- Joined
- Oct 6, 2019
- Threads
- 145
- Messages
- 2,542
- Reaction score
- 2,751
- Location
- Bluff City, TN
- Vehicle(s)
- 2019 JLUR (Mojito), 2022 JLR (Tuscadero)
- Vehicle Showcase
- 4
Any ideas on cost yet?
MendyOffroad
Well-Known Member
- First Name
- David
- Joined
- May 10, 2018
- Threads
- 3
- Messages
- 212
- Reaction score
- 446
- Location
- Phoenix, AZ
- Website
- www.instagram.com
- Vehicle(s)
- '21 392 Wrangler - Follow on IG @ mendyoffroad
- Build Thread
- Link
- Vehicle Showcase
- 1
Installed some KC Hilites Prosport Gravity Spot Pattern LEDS's on the A-pillar! Love the look of these!!
Mike630
Well-Known Member
These are awesome. Definitely my next move. How’s the hood glare at night?Installed some KC Hilites Prosport Gravity Spot Pattern LEDS's on the A-pillar! Love the look of these!!
Sponsored
