What did you do TO your Jeep JL today?

[lochado]

Finally made use of the MPS overhead panel & removed the clutter from the tailgate. The MyFax medic pouch pushes up against the Weathertech mat & curls it up. I can see just a little bit of it in the rearview, but it doesn't really get in the way & it's off-center since the straps don't line up with the panel slots. It's also easy to rip off & stash behind the seat to keep it out of view. The 14er pouch in front makes for a good place to hold vehicle paperwork so there's no reaching over to the glove box.

what overhead replacement is that?

Sponsored

 

[melendez69]

Stingy Mofos’ haha

what overhead replacement is that?

It's from Molle Platform Solutions. They offer a wider selection of panels for the JLU.

https://www.molle-platform-solutions.com/product-page/jlu-jl-fold-down-molle-tailgate-panel

 

[Carlton]

Recalibrated for larger tire size with the Tazer. Very thankful for the [Banned Site] video. Would have never figured it out without watching Eddie go through the process step by step. The Procal and Flashcal were much easier.

 

[thecritter]

Added a rack to the top. It can go full length but I did not put the extension in wanted access to the freedom panels.

 

[voodoo11]

Request vector... over
We have clearance, Clarence
Roger, Roger...
What's our vector, Victor...

Phone, Ham, Tablet for Gaimaps, CB, Handheld Ham.

 

[xtopherm]

I’m putting 35 inch tires on KMC rims. The off road guy was trying to convince me to get Ridge Grapplers but I chose KO2 because they’re a bit lighter and snow peak eating. Wimpy compared to the Nittos I know. I will have the dealer fix the Tpms do the sensors read correctly.
Not sure about lift yet.

This is not a debate I am eager to wade into, but it seems to me that if the catch cans are filling with oil that would otherwise be going into an air/fuel intake meant for a precisely measured air/fuel ratio, then they are doing

Installed the LOD Destroyer bumper. Battery died on my impact and I’m to lazy to use a ratchet, so the skid plate will have to wait.

Looks sharp. Ridge grapplers too. And I am a sucker for that grey. Good luck with the skids.

 

[Goblue]

Just a cheapo with good reviews off amazon since we needed center mounts and will see fairly limited use:
https://www.amazon.com/dp/B07259WYL7/ref=cm_sw_r_cp_tai_yhHCCbCJNB52T

cool thx

 

[nymarty]

Made a few little mods.
GPCA Tie Down Anchors with D Rings - like these because it makes it easier to take off the top and is great for hanging things up and stretching cargo nets across the cargo area.
Rugged Ridge Receiver Hitch - super easy to install on my JL bumper. Happy that I can tow again and use my cargo tray.
13” Rydonair antenna - Just like the look of it and no difference in reception.

 

[xtopherm]

First wash and wax....tomorrow we’re going to undercoat with fluid film

Let us know how the fluid film process goes. I am thinking of putting a bit of that in the frame rails and up and about in hard to reach areas before installing the bellypan. I figure it mostly can't hurt, but at the same time I am a little worried it will trap sand and that will hold moisture etc. Hope you'll be able to file a field report after applying. Good luck!

 

[xtopherm]

The axe was just a regular axe that I sprayed green and riveted to the tailgate plastic... the decals are from pixeldecals

I got the hatchet in my Jeep for $7 from the dreaded harbor freight. Even came with a composite yellow handle, which I suppose kinda matches my hellayella paint.

 

[American Jeeper]

This has to be one of my favorite mods, just because it’s “every day” useful:

 

[Hardybreed]

Smittybilt bumpers and winch install this weekend. Thought it would be easy, but I thought wrong. I have never seen sooooo much plastic with screws, bolts, nuts and braces, taking off the plastic bumpers. OMG totally over engineered. Glad I have some solid steel in front and behind me now.

I am now off road ready!

 

[EagleJL]

Installed the Mopar roof rack. It's going to hold an awning when it comes in.

 

[James_a]

This has to be one of my favorite mods, just because it’s “every day” useful:

I'll be doing this next week end, package is in the mail. I'll have to check out your install video.

After I'm done with that I get to install the Gobi Stealth rack sitting in my garage.

 

[Rubicon2019]

Let us know how the fluid film process goes. I am thinking of putting a bit of that in the frame rails and up and about in hard to reach areas before installing the bellypan. I figure it mostly can't hurt, but at the same time I am a little worried it will trap sand and that will hold moisture etc. Hope you'll be able to file a field report after applying. Good luck!

I was going to apply it today but the delivery came a little late so I’ll apply it tomorrow and try to take pictures or a video. Will definitely let you know how it goes.

Sponsored