What did you do TO your Jeep JL today?

[simpleJL]

Great job simple, I can't believe how cheap the camera is.
Can you show the camera installed and the location of that uconnect harness.
Thanks

Sponsored

 

[Jeepmarkjl]

I can snap a picture of the camera in a bit. Assuming you drill the right size hole it sits in there flush. I started drilling a hole dead center on my bumper not realizing there's a support bracket right behind it. Lol. So I have a small hole offset from the camera now.

And the Uconnect harness is behind the stereo itself. It is the main large harness connected to the back size of the radio. Fairly easy to get back there, and there is a YouTube video showing how to remove the JL stereo.

Define fairly easy. I watched the only video I could find and that seemed easy but then again it wasn't the 8.4 screen on a Rubicon.

 

[simpleJL]

Define fairly easy. I watched the only video I could find and that seemed easy but then again it wasn't the 8.4 screen on a Rubicon.

Just use a trim removal tool and pop off the panel where the push button start is.

Remove two 7mm bolts below the stereo screen (they hold the stereo trim on).

Pull the radio trim off. It's held on by 6 clips that pop out.

Then the radio itself is held in with (4) 7mm screws.

And boom, radio out.

It's actually the easiest radio removal I've ever had in a vehicle.

Can all be done with 1 trim removal tool, and one 7mm socket.

That video you watched of the sport radio removal is the exact same process for the 8.4" stereo.

 

[Jeepmarkjl]

Just use a trim removal tool and pop off the panel where the push button start is.

Remove two 7mm bolts below the stereo screen (they hold the stereo trim on).

Pull the radio trim off. It's held on by 6 clips that pop out.

Then the radio itself is held in with (4) 7mm screws.

And boom, radio out.

It's actually the easiest radio removal I've ever had in a vehicle.

Can all be done with 1 trim removal tool, and one 7mm socket.

That video you watched of the sport radio removal is the exact same process for the 8.4" stereo.

you rock. thank you

 

[jhonn236_AZ]

I broke the screen. Lol jk I didn't do anything back to the dealership!

 

[Grimm_E]

Did you install it with the top on or off?

I took the driver and passenger roof panels off and did those off the vehicle but I left the top on the back. I did put a piece of thin plastic down over the leather seats when I lightly sanded the ridges where the adhesive strips have contact.

The hardest pieces to get in were the ones in the center, but it was still easy. You just have to slide it into position and press it into the indentation. It was way easier than the all weather cargo liner install.

 

[mdallas]

Had the Mopar 2" lift installed yesterday!

 

[LydiaSP613]

I got my first glimpse at an actual picture of her & made an appointment to pick her up tomorrow!!!!! My Vida is coming home!!!!!

 

[Hughesonthenet]

My Ace Engineering JL Rock Sliders were delivered today! WOO HOO! Can't wait for Saturday so I can install them!

 

[drg6654]

My Ace Engineering JL Rock Sliders were delivered today! WOO HOO! Can't wait for Saturday so I can install them!

What was your waiting time?

 

[Lurvis33]

I got my first glimpse at an actual picture of her & made an appointment to pick her up tomorrow!!!!! My Vida is coming home!!!!!

 

[Rhinebeck01]

Well, I have done the following on the 2dr. Rubi, since yesterday at 1pm:

• Washed & Waxed
  
• 3M film applied to door sills and door hinges
  
• Installed Mopar Door Sill Guards
  
• Installed Gorilla Automotive Black Factory Style Wheel Lock System
  
• Removed Visor Stickers
  
• Programmed Homelink Remote
  
• Completed Install of 3rd Brake Light Relocation Kit
  
• Installed 6 D-Rings in Cargo Area
  
• Installed 2 Molle bags on backs of the front seats
  
• Painted Muffler & Tailpipe with black Rustoleum
  
• Drilled hole in Windshield Washer Reservoir Cap
  
• Installed WeatherTech Floorliners
  
• Installed AntennaX 24" CB AM/FM Antenna
  
• Installed OEM 8.4" Infotainment Center Screen Protector
  
• Installed Frt. License Plate bracket
  
• Installed license plates with stainless steel /black screws
  
• Installed Harley Davidson Trailer Receiver Plug
  
• Installed RavPower Red USB Power Adapter

Note: I made my own, through, exam of the underside of the JL.... No rust and all welds look aok.

 

[Grimm_E]

My Ace Engineering JL Rock Sliders were delivered today! WOO HOO! Can't wait for Saturday so I can install them!

Please let us know how long it takes you and how complicated it is. I would like to get these, and I am told that no drilling is necessary, but if you come across any pitfalls, please share.
Thank you

 

[JeepRubiCan]

Received my shocks from Accutune.

Nice what lift did you go with? How’s the ride?

 

[WildBlue]

My Ace Engineering JL Rock Sliders were delivered today! WOO HOO! Can't wait for Saturday so I can install them!

When did you order them? I’m going on almost 1 1/2 months and still waiting for them.

Sponsored