trim

I'm working on a lighting project, and I see these clips that snap into place. I've pulled, squeezed, and pushed them with and without a trim tool. Please help. I've attached some photos below to specify

Searching for 4dr OEM roll cage plastic trim from rear cross bar back. So this is the rear cross bar and the downturned angle pieces on the C-Pillar. Hey all, I obtained a section of the stock family bar that I'm going to turn into an art project. Unfortunately, it did not come with any trim...

Hey guys, I have been on the MOPAR 2020 Jeep JL site looking through schematic after schematic and cannot find this part. I was looking to put an alarm ID light on the passenger side by the air vents. (The other part on driver side is the Head Light Sensor) I'll attach an image, but was hoping...

Hi all! I just noticed today that the rubber coating on the airbag trim bezel in the center of the steering wheel is peeling. It comes off so easy. Has anyone else experienced this? If so have you done anything about it? I talked to the parts department to replace it and you have to change out...

OEM Mopar Jeep Wrangler JL Dash Panels Will fit 2018, 2020, 2021, 2022. Part #: 6AB19SD5AA Part #: 6AB27SD5AD Will need to be sanded and re-painted Does not come with air vents. You can reuse from your old dash. Make an Offer including shipping from SoCal.

As the title says. Looking for rear fender flairs. Doesn’t matter what trim they’re off. I prefer rubicon but they can be any trim. Painted or non. I ALSO NEED Rubicon fender flair liners for the front if you have some.

Selling my red dash In prestine condition No scratches I was super careful removing it when I replaced it with the black leather and red stitching dash No broken tabs, no missing tabs $200 picked up in San Diego or $240 shipped

Hey all, curious if anyone has cut or modified the oem plastic bumper. I’m eventually gonna get a steel shorty, but I’m curious if anyone has chopped the ends of their plastic one yet.

Hey everyone, I noticed older models have a tub rail trim kit that hides the ugly back rails when the hardtop is off. Do they make one for the jl. I can't find one anywhere. If not. Anyone make something they can give some ideas to make one.

Okay, so the Jeep Sahara trim is notorious for being ugly and getting painted black and that’s usually it. But I’m here to convince you to go with plasti dips gunmetal grey instead. Especially if you have a black or white wrangler. It matches almost perfect to the black trim on the underside of...

Bought both the titanium black and silver versions to see which I liked best with my decor. Decided to keep the silver ones and sell the black ones. These are brand new and never mounted. Just opened the package to inspect and compare. Also, this is a full set for the front dash and the rear...

Hello. I found that my 2018 JL was missing a few screws from the factory. The screws are the 3 trim screws that hold the large piece of trim around the dome light to the roll bar. Not only were the screws missing but the expansion(?) nuts are not in the roll bar. I found the screws but cannot...

A good friend of mine currently runs a carbon fibre and fibreglass factory. I asked him the other day if he could custom make certain parts for me (with personal touches), we then started to discuss what items could actually be carbon fiberized. So he’ll needed to 3D scan it, make...

Installed a silver center console cup holder trim piece. It looks factory and matches perfectly. I wasn’t a huge fan of the blank black space that is there around the upper trim of the cup holders. Ordered it on eBay for around $13.00 and it took about a week and a half to get to Texas. I may...

Question for those with a better grasp of the aftermarket and replacement parts market than me: Are there any alternative dash trim kits available yet? I've ordered a 2019 Mojito, which I love, but would like to do something with that bland silver dash. I'm thinking about pulling it and...

I noticed that my plastic cover over the fender vent was not flush. It appeared a tab was pushing against the fender metal where it seemed like a slot would be to accommodate the tab so the plastic would lay flush. I mucked with it and purposefully broke the tab off but another part of the...