Search results

Got everything installed finally and took the JLU down to Slade kentucky last weekend for a test run. Everything seemed to work fine. Didn't use the locker as we were more exploring than doing any harder trails. But the Jeep performed very well and didn't give us any issues. So for right...

Yep, marked and all fixed now. Deburred and cleaned up, should work fine now. Waiting for bearing to show up and put it back together.

Found it, this one is on me for missing. Once on the bench, pretty clear. Laying on back under Jeep, not so much. Differential lock plate and spacer are bent causing issues when the case tried to rotate. That 23 minute video actually called out being careful not to bend these parts as they...

Found a 20 page media file on spicer detailing EVERYTHING for the new Ford Bronco's. Even a schematic showing the diff assembly and the part number that is on MY locker that came in the ultimate Dana 44 for a JLU. Have found several media files for Jeeps, but nothing with that part number...

I think you are correct about the Rubicon note. The ultimate dana 44 has a four wire plug on it. One to the stator, one to what looks like a sensor, probably feedback for the computer. Since I have a JLU sport and am using a separate relay to power the locker, I should be good. Looks like my...

Well isn't that nice of them! I did find the part number stamped into the carrier 10039946 which on dana is called out as "Differential Case assembly Kit - M220 ELD". Being that the front and rear are the same, the M220 designation makes sense I guess. Seems like it is used on the JL M220...

So the saga continues.... Axle is finally installed in the JLU. But without axle shafts as the differential is clicking like a bad ratchet. I suspect that the locking ring or pins are damaged. So I now have a nice 2019 JLU with about $10,000 worth of axles, gears, 37's and am finally able to...

Been too busy to take the wife's Jeep off the street, so axle is still waiting for install. I am probably going to have to outsource the work if it is to get done, but life is good. Been wheeling and camping a lot, so not complaining. For the axle, I had it ordered for me and delivered to me...

"we able to get it". So dang giddy about getting the shaft, I can't type!:LOL: Still upset at Dana. Will have serious concerns about getting any assemblies or new hardware from them going forward when it comes to customer service.

So last week, a parts supplier I have been working with in Fort Wayne Indiana, called me and said the axle was in. Again. For the third time. He was dropping it off... IT LOOKS CORRECT!!! Good lord, it is the correct length, does not have the seal boss in the FAD location, has the machined...

Over 5 months and still no fix. My rep has talked to people at Dana and Mopar, no luck. That part number is NOT in the system is what I am told. If I go to the danaaftermarket.com site, that number does actually come up now, but it is not available. No stock... Sorry, but Dana sucks...

Honestly, I would be OK with that. But I can't even buy that. All I can find is the axles that have the FAD (two piece) or the one piece axle with the FAD delete. The problem is, the axle seal surface is located where the FAD was. The ultimate 44 does not have the hole in the axle for the...

Thank you for trying. The second link leads to a set of parts listed, but after they mention those shafts being used on the ultimate 44 and 60, all the parts they then list are for the stock JL and JT axles. Sitting in my garage right now is the 10044432, which is the outer half of the stock...

So, anyone know how to buy "Axle shaft RH inner front Dana 10047463" ? Dana site doesn't show up. Go to Mopar site and it doesn't show up. Trying to work with a vendor and I have now had two axle shafts delivered that are not the right part. I am starting to think that I have a very nice...

Good afternoon. I am in need for the passenger side axle shaft to an Ultimate Dana44 Advantek axle. Axle number is 10047716 although that is just the 4.56 gear option. I can not find anything on the replacement passenger axle shaft for a part number or how to get a replacement. This is a...

PM sent.

Very very interested, been trying to buy at least one set. Are these the same ones that come in the aftermarket "Ultimate Dana 44" for the JL? I think Dana Spicer 10048946 Performance Ball Joint Kit is the number and name. If so, I would be happy to buy them. Thanks.

Have wranglers with 5.7, 4.0 and 3.6L. 4.0 is favorite. That is a jeep motor! Doubt it is coming back though... oh well. FCA and electrical is just a scary thought.

10 things! Heck, I would settle for front leg room! How much crap do you have to put into the center area of the dash? I lowered the rear of the seat 1.5" and moved the whole thing back 1" so I now kinda fit at 6' 5". I know, taller than average. But I fit in my old CJ just fine, TONS of...

Did they regear it for you or a local shop/you? I need 4.56 gears and I am not finding anything available for under $5k ready to go. So it looks like my best bet is the rubicon rear axle and purchase a regear kit for $500 - $600. At least my JLU is fine, so I have time to get the parts.