Sponsored

Jeep humor waiting room ( ** NO POLITICS ** )

Blodgetter

Well-Known Member
First Name
Mark
Joined
Apr 11, 2018
Threads
0
Messages
609
Reaction score
3,266
Location
Burlington, VT
Vehicle(s)
2018 Wrangler JL Sport S (Eve)
:giggle: I like that.
Frankenstein said he might bring the CJ-5, but doesn't want red iron ore on that one. (or JRex, but I already won that argument too. :devil:)
Never met a woman whom lost an argument without doing so on purpose! My mother always used to say “I’m always right, even if I’m mistaken”

This is why I love them ;)
Sponsored

 

vonbek

Well-Known Member
First Name
David
Joined
Jan 16, 2018
Threads
6
Messages
949
Reaction score
4,318
Location
Georgia
Vehicle(s)
2018 Jeep Wrangler JLUR
I saw some chatter about removing the body bolts in order to install sliders. There's a thread on these forums about what a bitch it is to get them off. At least one person snapped off one of the bolts because it was cross-threaded from the factory. I guess it was quite a chore for the dealer service department to fix, too.
That's also part of my concern though I doubt any of mine are cross threaded
 

Steveo

Well-Known Member
First Name
Steve
Joined
May 15, 2018
Threads
10
Messages
36,865
Reaction score
270,610
Location
Sitting on the lap of someone you love
Vehicle(s)
'18 Wrangler JLUR, '23 F150 Rattler
Occupation
Retired Code Monkey
That's also part of my concern though I doubt any of mine are cross threaded
How big is the impact driver you're using? I have a 1/2" M18 Milwaukee that takes off lug nuts (torqued to 120+ ft. lbs.) without flinching. Might be worth picking one up.
 

wahlsaint

Well-Known Member
First Name
Todd
Joined
Jan 15, 2018
Threads
0
Messages
11,208
Reaction score
79,676
Location
Knopelandia, WA
Vehicle(s)
JLUR 6MT; Macan Turbo; Li'l Cooper; Subee, CR-V
What a pain in the ass! I managed to get all of the small ones installed, no problem. I managed to rip one of the big ones:headbang:, so I will be ordering another set. I’m finished for now because the sun came around and you can’t install in direct sunlight. I will say that the solution that you mix up is a lifesaver. I saw your post after I came in the house, otherwise I would have taken some pics. Basically, I prepped the area by using bug and tar remover. Then, you basically keep the area of installation wet, along with your hands and the 3M protectors and start applying to the hinge.
No worries, thanks tho. I'm sure there are some googlish pictures out there to check it out. We haven't determined if/ how often the doors will come off to decide whether to do this protection or not.
 

Sponsored

JEEPJL

Well-Known Member
First Name
Dan
Joined
Feb 13, 2018
Threads
6
Messages
18,460
Reaction score
93,278
Location
South West Florida
Vehicle(s)
2018 Jeep unlimted Sahara JL
Vehicle Showcase
1
I just got done doing some work on the door that goes from the house to the garage. It's not lined up quite right and was extremely hard to get the dead bolt to lock. I did somewhat of a Rube Goldberg fix but I don't care. I can lock it now without yanking up on the handle while turning the damn dead bolt key. The door rubs ever so slightly on the left side but not enuf to cause issues.
- double check the hinge screws ( they often come loose and will cause the door to be out of square)
- check the level of the door ( you experience cold to warm weather and ground shifting so it may have shifted out of plumb )

maybe !
 

JEEPJL

Well-Known Member
First Name
Dan
Joined
Feb 13, 2018
Threads
6
Messages
18,460
Reaction score
93,278
Location
South West Florida
Vehicle(s)
2018 Jeep unlimted Sahara JL
Vehicle Showcase
1
And lake effect makes you warmer than your northern neighbor. -30F a few times here... :asshat:
If it's 100 degrees out with 90% humidity I can still run down to the store for food

-30??? I'm starving for awhile !!
 

Smarrtazz

Well-Known Member
First Name
Trina
Joined
Jan 6, 2018
Threads
4
Messages
31,278
Reaction score
145,087
Location
Fl
Vehicle(s)
Lagertha 2018 JLUR Sting Gray ;)
So I can’t make this shit up! I went to install the sliders and as I took them out, after traveling thirty miles away to have my brother help me, we realized they sent me two passenger side rails. Not super happy right now.
 

obwahn

Well-Known Member
First Name
Mike
Joined
Feb 3, 2018
Threads
1
Messages
29,340
Reaction score
179,113
Location
Inland Empire
Website
www.youtube.com
Vehicle(s)
2018 JLR (Wrikki), 2018 Grand Sport (V)
Occupation
Retired puter dork
Vehicle Showcase
1
- double check the hinge screws ( they often come loose and will cause the door to be out of square)
- check the level of the door ( you experience cold to warm weather and ground shifting so it may have shifted out of plumb )

maybe !
I'm the idiot that installed the door to begin with. Pretty sure it's all correct except the stupid striker plates don't line up correctly. I've got it all working for now but I might check the plumb/level at some point.
Thanks Dan the Man!
 

Sponsored

obwahn

Well-Known Member
First Name
Mike
Joined
Feb 3, 2018
Threads
1
Messages
29,340
Reaction score
179,113
Location
Inland Empire
Website
www.youtube.com
Vehicle(s)
2018 JLR (Wrikki), 2018 Grand Sport (V)
Occupation
Retired puter dork
Vehicle Showcase
1
So I can’t make this shit up! I went to install the sliders and as I took them out, after traveling thirty miles away to have my brother help me, we realized they sent me two passenger side rails. Not super happy right now.
Dislike muchly! :no:
 

J.R. Quimby

Well-Known Member
First Name
Jake
Joined
Dec 23, 2017
Threads
2
Messages
5,230
Reaction score
31,856
Location
Waterville Maine
Vehicle(s)
2004 TJ Sport
upload_2018-6-24_13-25-42.jpeg
upload_2018-6-24_13-26-4.jpeg
Its actually rust. The natural iron in the ground. Its a b*tch to get off... Hoping to avoid the worst of it.
Ahh well, just wash even if it's a bitch not gonna stop me from having fun :rock:
 

Steveo

Well-Known Member
First Name
Steve
Joined
May 15, 2018
Threads
10
Messages
36,865
Reaction score
270,610
Location
Sitting on the lap of someone you love
Vehicle(s)
'18 Wrangler JLUR, '23 F150 Rattler
Occupation
Retired Code Monkey
So I can’t make this shit up! I went to install the sliders and as I took them out, after traveling thirty miles away to have my brother help me, we realized they sent me two passenger side rails. Not super happy right now.
Uhg! That sucks. There's nothing more frustrating than getting an incorrect/incomplete order. It happened to me earlier in the week.
 

CrazyKASG

Well-Known Member
Joined
Mar 4, 2018
Threads
0
Messages
16,835
Reaction score
82,267
Location
Minnesota
Vehicle(s)
2018 JLUR (JRex)
So I can’t make this shit up! I went to install the sliders and as I took them out, after traveling thirty miles away to have my brother help me, we realized they sent me two passenger side rails. Not super happy right now.
NOOOOOOOOOOOOOO! :swear:
Sponsored

 
 







Top