What products would you like Artec Industries to produce for your JL ?

[Artec]

We want some feedback to what kinda of Products you would like us to possibly produce for the JL .
For those who don't know what we do , Artec Industries is best known for our 1ton swap kits and replacement brackets, But we also make Link kits, Belly pans , Sliders, Bumpers, Tube fenders, and Inner fenders also.

Reply with what you'd like to see and there is a chance we may produce it !

Sponsored

 

[AZCrawl]

We want some feedback to what kinda of Products you would like us to possibly produce for the JL .
For those who don't know what we do , Artec Industries is best known for our 1ton swap kits and replacement brackets, But we also make Link kits, Belly pans , Sliders, Bumpers, Tube fenders, and Inner fenders also.

Reply with what you'd like to see and there is a chance we may produce it !

Don't you also build axle truss kits?

 

[theplankeye]

I would like fenders that nearlycover 37s (stock wheel geo, spaced out as minimal as possible). I also want those fenders and inner fenders to not have juvenile looking cutouts in them. Something small and tasteful is fine to show it is made by you.

 

[FCrackerJLRubi]

@Artec I have used your guys truss kits quite a bit, on my 8.8 swap in my TJ, to a full on 14 bolt swap in later on...kudos guys you make quality stuff. Aside from that I would imagine most of us that plan on using our new JLs are going to want to get right into sleeves, trusses, and gussets for these new axles (I know I will be buying a set of gussets as soon as possible).....I tweaked my 08 Rubicon front axle outers from not running guessets or sleeves and had to deal with the fallout from that for a few years...trying to get things straight again was a nightmare.

 

[Artec]

Don't you also build axle truss kits?

Yes, We do also build truss kits

 

[bongoray]

I'd like to see a mid-width bumper that has a recessed winch mount that accepts the factory JL LED fog lights, bull bar, powder coated with a place to mount a license plate. Too much to ask for?

Bongo

 

[pburke]

CB antenna mount that attaches to stock spare tire carrier where antenna will not interfere with rear wiper.

 

[pixeldecals]

Get those Aluminum Skids out guys! This came out for the JK after I was just about done building mine.

 

[jnutz]

You could get way ahead of the market if you could design the following:

Over window light bar mount

Rear license plate relocation bracket (need to ditch the stock rear bumper)

Rock rails/Side steps with some nice designs. (Your inner fenders and other mounts have really good designs to them)

Fenders that can somehow include the JL stock lights

 

[The Z]

Molded splash guards for JLU Rubicon because Mopar dropped the ball. They only have them for Sport and Sahara.

 

[Forgettable1]

Id likt to see rear facing light mount options. I like the ones that mount high on the glass hinges, but only "sorta"... The mounts I've seen all place the light above the roofline. Id like to see something that stays below the roof line but still uses that hinge for mounting. That or something that uses the taillights would work best for back up lights.

 

[JL1LE]

CB antenna mount that attaches to stock spare tire carrier where antenna will not interfere with rear wiper.

Bingo!

 

[Dreadnought_Leviathan]

Just waiting for the rear fenders so I can install them with my front ones.

 

[RockinMarine]

A CB/ trail flag bracket that mounts to the spare tire mount. Preferably with 2 holes like the JK mount has so someone can mount both a flag and CB antenna. Just looking at the bracket, its not too difficult to design. I just dont have the resources to make, or Id be making them by now.

 

[Cody6597]

Flat fenders with LED integration.

Sponsored