What did you do TO your Jeep JL today?

[J.boyd919]

I saw a YouTube video that used these rubber leg tips from Home Depot. I'm going to try these out in 2 weeks when I get my install done.

https://www.homedepot.com/p/Everbilt-1-in-Black-Rubber-Leg-Tips-4-per-Pack-49128/203661031

Oh sweet. Maybe I’ll try this with the garbage disposal hose spot above and combine the two!

 

[Mudawg10]

Added Rubicon suspension and 275/70/18 Ko2’s

 

[Moto_21]

Burns Canyon trail from Big Bear to Pioneertown.

Thats on the 2n02 trail? Howd i miss a giant hole lol

 

[Stormin’ Moorman]

C. Everett Coop has a JL?!

I was looking @brazos pic thinking “I’m pretty sure he resembles a surgeon general”, but I couldn’t put my finger on which one. Thanks for clearing that up. Lol

And @brazos at least he didn’t say you looked like Janet Reno.

 

[19 JLUR Bright Whit3]

Hello All! Its been awhile since I posted my jeep's changes. I swapped out the oil and filter (bought clearanced Mobil One filters. 8 of them for $3 each at Walmart), rotated the tires, added the UPR catch can, Installed the topsy hard top lift brackets, cut the hood vents bottoms out, installed a soft top.(got it from a local ad on CL for $550), swapped the the lower front spring pads with Rockwrawler ones (straighten out the mopar lift springs) installed the Teraflex trackbar relocation brackets.(front and rear)( The jeeps axles were off to the left 1/2 inch after the Mopar lift, now it's to the right .25 inch.)(If I had to do it over again, I would skip the relocation brackets, it rode better before) Added the RR third brake light ring and cancelled my RR HD Spartacus tire carrier. Ordered the EVO one. (RR wasn't going to ship until September)

View attachment 214958

View attachment 214959

 

[jessedoesitall]

Hey Guys,

I don't know who needs to hear this but ...I just checked out the Infotainment website and they are selling the HVAC Control panel kits with a jumper to get the volume and ac controls back after upgrading from the 5in radio.

https://www.infotainment.com/collections/all/products/jeep-wrangler-jl-hvac-climate-control-kit

 

[Carlton]

Absolutely nothing. Held up waiting on parts from Northridge. Going on 4 weeks.

 

[Martindfletcher]

Those look great. Are you going to run limiting straps?

Brett

I think it’s on the edge as to whether it’s optional or not. To be clear these shocks are 3/4 inch longer than RK’s spec. In the real world it seems ok, in the garage I can get the spring loose, but don’t think it can come out.

Also should note the front AAL inner fenders required some modification, it cut easy with Dremel, and I have a slight interference fit with elbow from shock to reservoir line. I got them on. I assume they will conform after the 37 smacks them a few times

 

[melendez69]

I saw a YouTube video that used these rubber leg tips from Home Depot. I'm going to try these out in 2 weeks when I get my install done.

These will work fine. Many of us have used this, or something similar, along with pvc.

 

[melendez69]

I need to do this..... haven’t been in hurry because my spare rests on my plasticrap bumper. The one and only good thing about it...... Is that 1” pvc? Irrigation pipe or schedule 40?

I used pvc risers... smaller, and easier to cut down to the nubby sizes I needed. Took me about 4 pieces to get it right.

https://www.homedepot.com/p/1-in-x-...8?MERCH=REC-_-pipinstock-_-NA-_-100208498-_-N

 

[COBoarder]

Hello All! Its been awhile since I posted my jeep's changes. I swapped out the oil and filter (bought clearanced Mobil One filters. 8 of them for $3 each at Walmart), rotated the tires, added the UPR catch can, Installed the topsy hard top lift brackets, cut the hood vents bottoms out, installed a soft top.(got it from a local ad on CL for $550), swapped the the lower front spring pads with Rockwrawler ones (straighten out the mopar lift springs) installed the Teraflex trackbar relocation brackets.(front and rear)( The jeeps axles were off to the left 1/2 inch after the Mopar lift, now it's to the right .25 inch.)(If I had to do it over again, I would skip the relocation brackets, it rode better before) Added the RR third brake light ring and cancelled my RR HD Spartacus tire carrier. Ordered the EVO one. (RR wasn't going to ship until September)

Well done Sir!!

 

[brazos]

I was looking @brazos pic thinking “I’m pretty sure he resembles a surgeon general”, but I couldn’t put my finger on which one. Thanks for clearing that up. Lol

And @brazos at least he didn’t say you looked like Janet Reno.

That’s funny! I saw that post following mine, and was puzzled by it. No clue. Can’t deny the resemblance, though!

 

[higbyz]

I parked it. Actually, day before yesterday. A week into a high-country camping/wheeling/escaping from Texas heat trip.

Done Engineer, Imogene, Cinnamon, and Last Dollar so far.

Got a nice little secluded camp above Telluride, and

chillin’ with my pups for a couple of days, before going wheeling again.

The Jeep IS the camp.

Joe

Great lookin dogs ! Mandatory companions ! Sally's better lookin than you.

 

[StrikeZ]

Warn winch installed, grill insert flipped, Mopar winch protector installed, Maximus license plate bracket installed, and KC HiLite Flex light installed.

 

[Bricazo]

I used pvc risers... smaller, and easier to cut down to the nubby sizes I needed. Took me about 4 pieces to get it right.

https://www.homedepot.com/p/1-in-x-...8?MERCH=REC-_-pipinstock-_-NA-_-100208498-_-N

guys these worked great for me.. you trim them to the length you need

https://www.amazon.com/gp/product/B01IDM1OCE/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1