What did you do TO your Jeep JL today?

[Swanny297]

Just wrapped up bull bar, light bar and led fogs

Now I better do a little TLC on the other cars, new tire and brakes for the Equinox this afternoon. Van....well who really cares about the van.

What light bar did you go on your bumper hoop? I have an LOD bumper and that light looks like it is about the right size.

 

[TJ2018]

Added Cool Tech roll bar mounting bracket for H3R quick release mount and fire extinguisher. Very easy install, super solid. Highly recommended.

(See this thread for more info: https://www.jlwranglerforums.com/fo...ire-extinguisher-kit.24534/page-2#post-642298 )

 

[klhjeep2018]

Added Cool Tech roll bar mounting bracket for H3R quick release mount and fire extinguisher. Very easy install, super solid. Highly recommended.

(See this thread for more info: https://www.jlwranglerforums.com/fo...ire-extinguisher-kit.24534/page-2#post-642298 )

Installed mine today too. The only difference is my extinguisher is black, great product. Highly recommended as well!

 

[IndustrialAction]

Where did you find the Racor? I can't find it in stock anywhere.

I bought one NIB on Facebook marketplace for $100

 

[MikeJLURubi]

So little stuff today. I put in an OCD storage organizer, tail light protector, and finally got my new personalized plate yay!

Are those the tape-on Taillight protectors? Will they work on the LED lights?

Thanks

 

[lbau317]

Finished machining and assembled my new stubby bumper. Made of 6061 aluminum plate, 3/4" thick winch plate, 5/8" thick front plate, 1/2" thick support plates. Has stainless hardware and weighs in at approximately 50# What do you think, leave natural, or powder coat black leaving the stainless fasteners natural? TIA!

 

[Fire Burns]

Finished machining and assembled my new stubby bumper. Made of 6061 aluminum plate, 3/4" thick winch plate, 5/8" thick front plate, 1/2" thick support plates. Has stainless hardware and weighs in at approximately 50# What do you think, leave natural, or powder coat black leaving the stainless fasteners natural? TIA!

Powder coat for sure!!!

 

[AZ-Matt]

Which winch guard is that?

Its the Maximus-3

 

[Tritonman]

Front bumper
Winch
Bumper skid plate
20" LED bar in bumper
Tinted side markers
Dual Pod A pillar mounts
4 2" RGB pods
Added the sequential turn signals, but that was last week.

 

[Kenny]

Its the Maximus-3

How hard was the install? Looks great

 

[Rdmitch]

The light bar is a cheepy eBay special. It’s 20” and I wish I would have ordered a 24”

I wanted it to go on the lower bar which have holes at 17” apart. The light actually measured 19” and with the brackets the way it’s built I could not make it fit, so it went onto the top.

Not the greatest quality, but it actually works well and was a snap to install and wire.thank you Jeep for providing a spare hole in the firewall! Eventually I’ll replace it with a 24”
Next year we dump front plates in Ohio so that will be the time to make the switch.

 

[johnparjr]

Well this is installed twice I put them on the wife didn’t like them took them off and then a week later I Jedi mind tricked her into trying them again

Rokblokz with custom lime green logo which they didn’t have listed but they said they would do and they did

 

[OMTBiker]

Added some cross bars for a roof basket for the upcoming trip to Acadia National Park, the basket will only be on for trips as it will not fit in the garage installed.

 

[dustanner]

Replaced my Rubi rails with Rugged Ridge XHD rails but I’m not happy with them. On side just doesn’t fit. I’ve adjusted as much as I can but no luck. The mounts are just off and the hardware is chintzy. Not recommended.

Anyone have tips on returning 150lbs to Quadratec?

 

[parrotheadphan]

After mowing the lawn this morning, I spent the afternoon washing and detailing the Jeep. Then took her for a drive and some ice cream.