Mx5red
Well-Known Member
That looks fantasticInstalled my new aluminum bumper from Next Venture Motorsports
That looks fantasticInstalled my new aluminum bumper from Next Venture Motorsports
Love it!That looks fantastic
Looks like about 8” lift over stock Sport.Changed up some spring rates, new oil, seals and revalve in all the shocks and new seals in the bumpstops. Shes a tall SOB, front driveshaft no longer works without feeling like im in a vibrating chair, if i rotate the pinion enough to make it work the bumpstop strike pads might as well have lights on them and be headlights. But she sure does look good!
Also added a 15watt midland micro mobile to the girlfriends jeep and a locking gas cover
I'm with ya... I liked the look even though I was skeptical of the vulnerability to the elements. Since I'm not that smart, I still wanted to try them out.My thoughts exactly. I was irritated enough that I didn't contact them. I'm going to soak the locks in some lubricant and see if they work again, but they're not going back on.
I liked the look, but they were inconvenient as hell. PLUS an offroad vehicle exterior part that is vulnerable to dust and water? C'mon now...
Those plastic retainer clips are a pain in the ass and they're $4 each (not a typo). This set on the Amazon has 6.4 & 6.3mm clips that fit. The heads on the 6.4's are the type that will also snap off.Maybe a 2? I’m kind of new to doing mods on my Jeep. For me, removing the hood insulation liner was pretty annoying because it almost starts to crumble and I pretty much broke every retention clip. Using Rapid Tac helped a lot with allowing me to place the decal and pushing air out before it started sticking. The hardest part was getting the edge to conform to contoured front of the Rubicon hood (which is called out in the instructions. Just be patient when you do it.
Perfect - thanks! My goal is to add some under-hood lighting before clip everything back in. Ordered this to have on hand though.Those plastic retainer clips are a pain in the ass and they're $4 each (not a typo). This set on the Amazon has 6.4 & 6.3mm clips that fit. The heads on the 6.4's are the type that will also snap off.
You should be able to find only what you need since 240 pieces may be overkill when you only need a dozen. My ladyfriend isn't the best driver & I've found myself using these for her car.
Same here, I was missing the rectangular Winch spacers. They were shipped to me overnight. Great bumper!Installed a Rock Hard 4X4 Patriot Series Mid Width Aluminum Bumper. Unfortunately, some hardware was missing so couldn't continue the winch install, gotta call them during the week. Nonetheless, digging the new look
Thank you sir. Going to do this and the vent decals.Maybe a 2? I’m kind of new to doing mods on my Jeep. For me, removing the hood insulation liner was pretty annoying because it almost starts to crumble and I pretty much broke every retention clip. Using Rapid Tac helped a lot with allowing me to place the decal and pushing air out before it started sticking. The hardest part was getting the edge to conform to contoured front of the Rubicon hood (which is called out in the instructions. Just be patient when you do it.
Looks great!Finally installed the metal cloak 6 pak shocks and their 3.5” lift springs. While at it installed king bumps in the front. Only went around the block but so far ride is a lot more controlled is the best way to describe it. Going on a shake down run tomorrow. Still have to get longer front sway links and trim the rear lower mount for more clearance but was on a tight schedule with having toddlers in the house.
Its pretty close hahahaLooks like about 8” lift over stock Sport.
looks awesome
Actually i think you are spot on hahahaha good guessing, im at like 6 over rubiconLooks like about 8” lift over stock Sport.
looks awesome
Nice. I had those on my RAM 1500. Loved them. Just got a 2021 Rubicon. What model year is your Jeep. GoRhino says these "are not made for the 2021 Jeep" but I cannot imagine the holes underside changed since the stock rails are compatible from 2018 on... unless the pinch seem hole moved?Mounted the Go Rhino RB20 steps. Pretty easy to install. I’m pleased that (1) they will prevent some of the kick up of rocks etc.. (2) they are nice and functional and (3) they cover a lot of the pinch seam.