I think your's is bent.I tried the Rampage tonneau cover and didn't have the same experience others seem to have had. The driver-side corner tab won't fit into the channel; I don't know if it's too thick, or if the channel is too narrow. The fit is good, not great, and the corner just sits there & flops around. It's a pain in the ass trying to whittle the tab down.
ok, got it. with the filler plate, does it line up evenly with the mopar winch plate. or is it being stacked up to use the same mounting points. a;so as far as i can tell, you can use the maximus filler plate with the maximus winch plate.The winch is a Zeon 10-S. The winch mounting plate we used is a Mopar kit (part #82215182AC), the Maximus-3 filler plates are these little jewels that fill the gap between the bumper and the frame. They really clean up the look: https://maximus-3.com/home/jl-filler-trim-plates-zeon
The front bar is the Mopar "Grille and Winch Guard"(part #82215351). It does mount with two bolts on each side and has plenty of clearance for the winch. My wife looked at the options from Warn and others but kept coming back to the Mopar as her favorite.
Rig looks killer!Installed a Warn Zeon 12S Platinum Winch. Can't wait to get back out on the trails and put it to work.
The body tab appears to be bent up against the body tub. You might try using a plastic trim tool as a prybar working from the outside in to see if you can pry it back out.
I got the smittybilt tailgate bar for the jk ... it fits.... the retainers snap on... to remove them, you press down on them and slip a plastic trim remove tool under the front lip and it comes off.I tried the Rampage tonneau cover and didn't have the same experience others seem to have had. The driver-side corner tab won't fit into the channel; I don't know if it's too thick, or if the channel is too narrow. The fit is good, not great, and the corner just sits there & flops around. It's a pain in the ass trying to whittle the tab down.
Thanks!!!
Ha! Yep!Looks like Warn is having a good week with @PalmettoMike, @RagTopDeluxe and us all installing a Warn this week.
We did the Zeon 10-S along with the usual Factor 55 stuff and the Maximus-3 Filler plates. I love the way the Maximus filler plates clean up the look.
Interesting thing about the install was that we actually used the setup today for recovery after some of the folks we were with got into some heavy snow in the Sierras. Everything worked out perfectly.
I may have to try this try this if bending outwards doesn't work... thank you for the tip.I got the smittybilt tailgate bar for the jk ... it fits.... the retainers snap on... to remove them, you press down on them and slip a plastic trim remove tool under the front lip and it comes off.
The only modification you will need to do will be put velcro on a corner... you will see which one.... and it keeps it tight and no flapping....
You may be right... It's noticeably tighter than the passenger side... it slid in with no problem.
Thanks for the link.The winch is a Zeon 10-S. The winch mounting plate we used is a Mopar kit (part #82215182AC), the Maximus-3 filler plates are these little jewels that fill the gap between the bumper and the frame. They really clean up the look: https://maximus-3.com/home/jl-filler-trim-plates-zeon
The front bar is the Mopar "Grille and Winch Guard"(part #82215351). It does mount with two bolts on each side and has plenty of clearance for the winch. My wife looked at the options from Warn and others but kept coming back to the Mopar as her favorite.
The lip on mine is right also..I can't fit the plastic tab underneath...
