Sunrider Tops for JL?

[Krondor]

What do you get with the LiteBriye code?

$75 towards your next Bestop purchase...

Advertisement

 

[Kevin8086]

What do you get with the LiteBriye code?

$75 off coupon for future purchase and entered to win a special prize from the “LiteBrite” channel separate from bestop.

 

[Bestop]

Hey guys,

Check out our install video for the Sunrider for Hardtop:
Don't forget to purchase your Sunrider for Hardtop by tomorrow to get the $200 savings! Also, it is confirmed, the Sunrider for Hardtop for JL WILL WORK on the newly released Gladiator!

CassieAtbestop

 

[Rhinebeck01]

Well, that is a very decent video that DOES cover the assembly and install quite well.

Geeeeeeeeeeez, he makes the insertion of the Z-Clip look so easy.

Guess that is a result of inserting quite a few Z-Clips.

First timers doing the Z-Clip install, do expect to take a few minute doing what he did in 6 seconds. 8-)

 

[Bubba33]

Well, that is a very decent video that DOES cover the assembly and install quite well.

Geeeeeeeeeeez, he makes the insertion of the Z-Clip look so easy.

Guess that is a result of inserting quite a few Z-Clips.

First timers doing the Z-Clip install, do expect to take a few minute doing what he did in 6 seconds. 8-)

See how he worked on it off a table, as he had it opened. It was easy for me.

 

[anotheraznguy]

The video made the z-clip a lot easier. Got it in without any issues. One question i had is one side of the latch goes on easy and the other side has a lot of tension. should i adjust anything or leave as is.

 

[anotheraznguy]

FYI for those curious about removing the bestop emblem.

There is nothing underneath it and it comes off cleanly and quickly
I just heated it up with a heat gun for a few seconds. Used a plastic trim tool and popped it right off. I didnt even need to break out the goo gone since it came off clean.

Here is just an example of what i used and what it looks like removed

 

[Bubba33]

FYI for those curious about removing the bestop emblem.

There is nothing underneath it and it comes off cleanly and quickly
I just heated it up with a heat gun for a few seconds. Used a plastic trim tool and popped it right off. I didnt even need to break out the goo gone since it came off clean.

Here is just an example of what i used and what it looks like removed

Looks like you just opted out of the drawing. LOL

 

[anotheraznguy]

i ordered through Morris 4x4 so i wasn't entered into a drawing.

 

[DanW]

The video made the z-clip a lot easier. Got it in without any issues. One question i had is one side of the latch goes on easy and the other side has a lot of tension. should i adjust anything or leave as is.

Mine was that way. Just double check that everything looks right, and if so, don't worry. It will loosen up. Mine is perfect after a week and a half and some driving around. Of course, it is cold here. If it is warm there, then just a little time in the sun should do the trick.

 

[Bubba33]

Mine was that way. Just double check that everything looks right, and if so, don't worry. It will loosen up. Mine is perfect after a week and a half and some driving around. Of course, it is cold here. If it is warm there, then just a little time in the sun should do the trick.

Passenger side was tight, one afternoon in the sun and its fine. My soft top was the same way.

 

[Bearman95]

See how he worked on it off a table, as he had it opened. It was easy for me.

 

[Bearman95]

I worked off the table also, I had to use a pair of locking needle nose vice grips to hold that sucker up there! I got it done but it certainly wasn’t easy! LOL

 

[Bubba33]

I worked off the table also, I had to use a pair of locking needle nose vice grips to hold that sucker up there! I got it done but it certainly wasn’t easy! LOL

I sure didnt see that it was hard. I had to take my fuel pressure sensor off my hemi on my ram today. Now that was a lot harder than the z clip.

 

[jfutty]

I am ready to get one today. Which fabric did everyone get?