Sponsored

Show your DIY mods that made you feel like a genius.

DieselTrooper

Member
Joined
Feb 4, 2021
Threads
4
Messages
15
Reaction score
28
Location
florida
Vehicle(s)
2020 JLU Sahara Altitude 3.0 Diesel
Move thread if necessary

Show anything DIY (interior or exterior) that either you can’t live without, made you feel like a genius, or might not have been done before.
Sponsored

 

Jeeperz Kreeperz

Well-Known Member
Joined
Jan 15, 2018
Threads
40
Messages
454
Reaction score
490
Location
New Hampshire
Vehicle(s)
2021 JLUR 4xe
Customized my DFG Fridge Slide to fit the EXTREMELY tight tolerances due to Trailgater Tailgate table, and 4xe battery trim that shortens the cargo area.

I had to make the following mods:

1. Hack saw front left corner of slide frame
2. Hack saw both rear corners of slide frame
3. Flip rear tie-downs 180 degrees and move to inside of slide tray
4. Drill two relief holes in rear battery trim panel to get that last 1/4 inch

Then, to really kick it up a notch, since mounting the fridge slide kills my access to the vehicle jack, and rear cargo cubby, I installed a low profile marine inspection hatch to reclaim that lost cubby:


Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 86E9A6C9-80D9-4D85-B20C-9B860B1C041B
Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 5104F4D2-6AF3-4BBB-A2F8-E5E77204ACDD
Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 54A12AB1-3D39-4489-8F54-273038A47D6C




Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 3AE135E3-19E1-416F-80E7-A677EE95EE16
 
Last edited:

Sponsored

LittleDog

Well-Known Member
Joined
Jan 16, 2020
Threads
33
Messages
648
Reaction score
925
Location
New Jersey
Vehicle(s)
2020 Sahara JLU
Customized my DFG Fridge Slide to fit the EXTREMELY tight tolerances due to Trailgater Tailgate table, and 4xe battery trim that shortens the cargo area.

I had to make the following mods:

1. Hack saw front left corner of slide frame
2. Hack saw both rear corners of slide frame
3. Flip rear tie-downs 180 degrees and move to inside of slide tray
4. Drill two relief holes in rear battery trim panel to get that last 1/4 inch

Then, to really kick it up a notch, since mounting the fridge slide kills my access to the vehicle jack, and rear cargo cubby, I installed a low profile marine inspection hatch to reclaim that lost cubby:


Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 20190216_144323
Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 20190216_144323
Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 20190216_144323




Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 20190216_144323
Good job reclaiming this. That cubby can hold an incredible amount of tools.
 

rkwfxd

Well-Known Member
First Name
Rich
Joined
May 24, 2021
Threads
37
Messages
1,117
Reaction score
2,115
Location
Whittier
Vehicle(s)
2021 JLR, 2020 Tahoe 4x4, 2006 Tundra, 1990 964
Occupation
Unemployed

Boatbuilder88

Well-Known Member
Joined
Mar 13, 2017
Threads
16
Messages
1,069
Reaction score
2,162
Location
New Jersey
Vehicle(s)
'19 Wrangler JL Sport S
Occupation
F-16 Engineer (retired)
Removed the visor nanny stickers...

Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 20190216_144323
Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 20190216_144323
Old thread but…How?
Use a hairdryer to heat up the glue. Peel the sticker off at 180 degrees. Work slowly. It will look like the underlying vinyl is pulling up with the sticker. Don't worry, the vinyl will quickly shrink back down onto the visor.
 

rkwfxd

Well-Known Member
First Name
Rich
Joined
May 24, 2021
Threads
37
Messages
1,117
Reaction score
2,115
Location
Whittier
Vehicle(s)
2021 JLR, 2020 Tahoe 4x4, 2006 Tundra, 1990 964
Occupation
Unemployed
Use a hairdryer to heat up the glue. Peel the sticker off at 180 degrees. Work slowly. It will look like the underlying vinyl is pulling up with the sticker. Don't worry, the vinyl will quickly shrink back down onto the visor.

Thank you
 

Sponsored

GtX

Well-Known Member
First Name
David
Joined
Nov 9, 2019
Threads
8
Messages
1,913
Reaction score
3,010
Location
Illinois
Vehicle(s)
2020 JLUR 3.0D
Occupation
Working for the man.
Vehicle Showcase
1
Fabricated some KC Cyclones for cabin lights.
On dimmers.
In red.

Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 20220417_172630


Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 20220417_172635


Jeep Wrangler JL Show your DIY mods that made you feel like a genius. 20220417_172904
 

Dagwood

Well-Known Member
First Name
David
Joined
Mar 4, 2019
Threads
15
Messages
489
Reaction score
950
Location
Alabama
Vehicle(s)
2019 Jeep JL, 1999 Jeep xj, 2008 Scion XB, 2015 Scion XB, 1966 Ford F100, 1969 Oldsmobile
Molle panel made for pelican case lids can be repurposed for other things. I used on the sides of rear cargo rack made for 4 door in my 2 door. The panels release with latches for quick detachment.
20220716_091147.jpg
Sponsored

 
 



Top