Scangauge Questions

[C0ach78]

Just got the wire routed for my Scangauge and was going through the set up. I can’t seem to figure out how to monitor soot level, regen status, exhaust temp, and turbo pressure. Anyone have a good guide, video or something to help? Searched the forum and didn’t see anything but could have missed it.

edit: I figured how/where to enter the X Gauges but can’t seem to find one for turbo pressure. Also I found 3 different exhaust temps but have no clue what they are. Lastly I seen a video with someone monitoring turbo temp but don’t see a code for that either.

Sponsored

 

[Capricorn]

You have to program blank XGauges. You have to enter the 4 sets of commands for each XGauge and give it a name.

The commands are in the link below for EcoDiesel.

https://www.scangauge.com/x-gauge-commands/3-0l-ecodiesel/

 

[Capricorn]

This is a snapshot of the gauges you can program for EcoDiesel.

 

[rickinAZ]

Lastly I seen a video with someone monitoring turbo temp but don’t see a code for that either.

Going from memory here: I think the boost pressure is one of the standard gauges that you can access without programing an X Gauge. Exhaust #1 is turbo temperature.

 

[C0ach78]

Going from memory here: I think the boost pressure is one of the standard gauges that you can access without programing an X Gauge. Exhaust #1 is turbo temperature.

Is there a place to look up what each exhaust is? I read the book again don’t see boost pressure anywhere.

 

[Capricorn]

Is there a place to look up what each exhaust is? I read the book again don’t see boost pressure anywhere.

Page 17 of the manual. Is this what you were looking for - the boost part? In the Advance Setup, choose BST instead of MAP.

 

[C0ach78]

Page 17 of the manual. Is this what you were looking for - the boost part? In the Advance Setup, choose BST instead of MAP.

I seen that but was getting some really high numbers. For fuel selection it should be diesel a correct?

 

[Capricorn]

I seen that but was getting some really high numbers. For fuel selection it should be diesel a correct?

Correct - Diesel a.

 

[BEEBOB]

Sorry maybe a dumb question. You only see four settings at a time but can have multiple pages to go through, am I understanding that right

 

[Capricorn]

Sorry maybe a dumb question. You only see four settings at a time but can have multiple pages to go through, am I understanding that right

Correct, you can program multiple xgauges, but on the screen, you can only display 4 at a time.

 

[BEEBOB]

Correct, you can program multiple xgauges, but on the screen, you can only display 4 at a time.

Thanks

 

[Capricorn]

It will be awesome if Scangauge can go wireless and have an app or even a display unit that has bluetooth to the OBD like BlueDriver.

I downloaded the BlueDriver app (don't have the scanner yet) but the only thing preventing me from getting it is the parasitic battery drain concern when left in the OBD2 port. Have anyone used BlueDriver and if the concern for battery drain true?

 

[TIPOVR]

Bumping an old thread but just ordered my scanguage2. Autozone doing a 20% off promo until May 8th (promocode save2day), so $136.12 total with next day delivery.

 

[mudog]

Bumping an old thread but just ordered my scanguage2. Autozone doing a 20% off promo until May 8th (promocode save2day), so $136.12 total with next day delivery.

Thanks for the info. Just ordered one from Autozone

 

[Black Betty 2.0]

Does the San guard go directly into the OBD or do you need the bypass cable ?

Sponsored