mwilk012
Well-Known Member
Were they used axles? That’s hella cheap.No. I replaced both front and rear.
Sponsored
Were they used axles? That’s hella cheap.No. I replaced both front and rear.
Bingo. You buy a sport to save money on the monthly payments, then upgrade to better than rubicon as time permits. That way you can have a better than a rubi, without the higher payment, and with all that extra cash, get you some extra shots of whiskey at the bar (or perhaps a steak if you dont drink) on the weekend .Exactly. Don't make it a Rubicon. Make it better than one.
I have the Xpel on my jeep (the entire front - hood, grill, around the windshield) and couldnt be happier...looks brand new everydayAs mentioned above, there are a few more things to get all the Rubicon mechanicals. Also, there are some software items, which I think I read that the Tazer can activate as a selectable.
As for swapping any more of the Rubicon parts in, it just depends on whether you'll need them for what you do. 4:1 xfer case and lockers are mostly a rock crawling thing. The Dana 44s are more to take loads from large tires and intermittent traction and some hard pounding. I didn't see where you posted your axle gear ratios. A Rubicon has 4.10:1 gears standard. A Sport has 3.45:1 gears. If you go with 35" or 37" tires, lower gears will help both on-road and off. Big tires rob acceleration performance, fuel economy, and braking performance like a bandit.
The electric swaybar disconnect is more Barbie stuff. It allows you to push a button on the dash to disconnect the front swaybar which allows the suspension to more freely articulate. The same thing has been done manually with inexpensive quick disconnect links on the swaybar for decades. But you have to get under the vehicle and get dirty. Again, not a feature needed for driving on a typical 2-track trail. More crawler stuff.
One fairly pricey mod I'm considering for my Rubicon is some type of film paint protection, like vinyl or the Xpel stuff. My use puts me in 2-track trails with overgrown brush that curls the paint off a vehicle. Being an old man that just goes places to hunt birds with my birdog, I'm sure I coulda got by fine with a stripped down Sport and some bigger tires and a take-off suspension from a Rubicon and a winch.
I was looking through the Mopar accessories guide, and I noticed there's a couple of part numbers referring to both front and rear Rubicon D44 axles. Both contain 4.10 gears, and e-lockers as you might expect. List pricing is 2695, and 2295 respectively. Of course not including installation.Santa Monica Jeep is the one who is ordering and installing everything.
This!I was looking through the Mopar accessories guide, and I noticed there's a couple of part numbers referring to both front and rear Rubicon D44 axles. Both contain 4.10 gears, and e-lockers as you might expect. List pricing is 2695, and 2295 respectively. Of course not including installation.
Something you'll want to ask your dealer, are they installing the locker switchgear in your cabin? Typically the switchgear is located on the very bottom/left side of the dash in red. I cannot find a part number for that, however, you'll want to speak to them about that if you've not done so. Might as well take advantage of the lockers since your installing them.
I was considering a Sport S, and Rubi when purchasing, I just decided on the Rubi since I didnt want to have to build up at that time. To each his own, but a Sport S is a great starting point, and to another's comment will equal a better Rubi in the end with the non-OEM aftermarket accessories.
What’s the difference in fun between the 2?Well, fully half of the fun in Jeep ownership is modifying them. Have fun!
OP says Jeep dealer is ordering and installing everything -- aside from $$ for all the parts, I wonder how much they are charging for all the labor. Installing the parts yourself is one thing, but the $$ spent on labor (especially from a dealer) can get pretty hefty.What’s the difference in fun between the 2?
-buying a Rubicon
-buying a sport S, rubicon parts, and paying someone else to do the work to swap parts
Seems like the long way to get to the same point.
You’re going to end up at Rubicon pricing or more, with no real benefits over buying a Rubicon to begin with. I could see doing the work yourself, if not for anything other than personal enjoyment. Reminds me of the people who put huge “built not bought” stickers on their JK’s, that they bought, with the aftermarket parts that they bought, and installed by someone else’s labor that they paid for.OP says Jeep dealer is ordering and installing everything -- aside from $$ for all the parts, I wonder how much they are charging for all the labor. Installing the parts yourself is one thing, but the $$ spent on labor (especially from a dealer) can get pretty hefty.
Maybe the owner is looking for a sleeper Sport model.What’s the difference in fun between the 2?
-buying a Rubicon
-buying a sport S, rubicon parts, and paying someone else to do the work to swap parts
Seems like the long way to get to the same point.
I enjoy cheaper insurance cost, cheaper monthly payments and that savings is reinvested into my Jeep. I choose how my money is spent not someone else suggesting what is necessary. What point is it to have a Jeep, if you can't make it your own?Maybe the owner is looking for a sleeper Sport model.
Or maybe the dealer ordered a Sport by mistake and is taking full responsibility by turning it into a Rubicon.
I’m not sure the math works out but to each their own.I enjoy cheaper insurance cost, cheaper monthly payments and that savings is reinvested into my Jeep. I choose how my money is spent not someone else suggesting what is necessary. What point is it to have a Jeep, if you can't make it your own?