License Plate Relocation Options

[Ryanfold]

I need to start looking at options. Whats everyone using?

Sponsored

 

[johnparjr]

stock bumper

 

[Halstem1]

Same question. Looking to relocate to the spare. What are the options out there? Obviously want to keep camera and plate/brake light. I was looking at motobilt. I think Rugged Ridge was supposed to come out with an option. What else?

 

[TxJeepers]

I used a combo Artec and Poison Spyder setup. I just saw though that Posion appears to have full setup of their own which might be good. I think its a new part, 41-08-030. You'll have to contact them direct.
Here is what I have going on.

 

[JeepNomad]

I just ordered an LOD relocation bracket. I also have an LOD bumper on the way but i'm sure it will fit other bumpers. By the way, if you are in doubt about fit call LOD Offroad. They are very nice and will find the answer to any, and all, questions. No I don't work for them. LOL. Also, if you order through Northridge 4x4 it's cheaper and you can use "LITEBRITE" coupon code to get 10% off. No, I don't work for them either! LOL.


https://www.northridge4x4.com/part/...1-lod-rear-license-plate-relocation-kit-black

 

[cw2020]

I originally got the Metalcloak relocation kit when I got their rear bumper. I hated it and the instructions weren't correct, so I got a bumper mount relocation bracket from Texas Metal Works

https://www.texasmetalworks.com/product/license/

This thing is awesome and suuuuper beefy. It comes with the LED light and you just splice into the factory harness.

 

[Halstem1]

I originally got the Metalcloak relocation kit when I got their rear bumper. I hated it and the instructions weren't correct, so I got a bumper mount relocation bracket from Texas Metal Works

https://www.texasmetalworks.com/product/license/

This thing is awesome and suuuuper beefy. It comes with the LED light and you just splice into the factory harness.

curious to see it mounted.

 

[higbyz]

I need to start looking at options. Whats everyone using?

I am in a federal govt witness protection program. They have relocated my wife and me . ( my plates have come with me ) Unfortunately , I cant reveal the new location.

 

[ChattVol]

I originally got the Metalcloak relocation kit when I got their rear bumper. I hated it and the instructions weren't correct, so I got a bumper mount relocation bracket from Texas Metal Works

https://www.texasmetalworks.com/product/license/

This thing is awesome and suuuuper beefy. It comes with the LED light and you just splice into the factory harness.

Pics?

 

[Carlton]

I'm not a fan of relocating the plate to the spare. I bought the Aries relocation bracket which is for a front bull bar bumper. I was able to use it on my rear bumper with a light I bought off ebay.

I drilled three holes in the bumper. I used the two outside holes to mount. I ran the wire for the light through the center hole. I used the wiring harness from the stock bumper so I could just plug in without hard wiring.

 

[LLANERO]

Built my own:

 

[rustyshakelford]

I originally got the Metalcloak relocation kit when I got their rear bumper. I hated it and the instructions weren't correct, so I got a bumper mount relocation bracket from Texas Metal Works

https://www.texasmetalworks.com/product/license/

This thing is awesome and suuuuper beefy. It comes with the LED light and you just splice into the factory harness.

curious to see it mounted.

Pics?

These are great. Made out of 3/16th and super beefy. Heavier gauge than all bumpers I’ve seen on the market. Use two butt connectors and it retains the factory wiring harness! Laser cut and powder coated

Brett

 

[Smart_Hulk]

Using motobilts relocation kit.

 

[ChattVol]

These are great. Made out of 3/16th and super beefy. Heavier gauge than all bumpers I’ve seen on the market. Use two butt connectors and it retains the factory wiring harness! Laser cut and powder coated

Brett

Wish it didn't stick out past the body on the side and am not sure why a license plate holder needs to be made of steel thicker than a steel bumper. Is the MFG thinking the license plate holder is going to act as armor?

 

[cw2020]

These are great. Made out of 3/16th and super beefy. Heavier gauge than all bumpers I’ve seen on the market. Use two butt connectors and it retains the factory wiring harness! Laser cut and powder coated

Brett

Thanks Brett, I was late to the game posting pictures

Sponsored