KIWI Master 9" JL LED LIghts

[David F.]

Just ordered the light as well
As the fog lights you recommended.
Now that you have had them a week or so, you still Like them?

I do, still getting flashed even when I lowered them (not as much but some) but the lights match well and look good.

Sponsored

 

[Pemberton325]

Just got my lights and fogs installed tonight. I am happy with the look.

 

[Pemberton325]

So....after weeks of trying to get the lights adjusted, I can’t get them low enough without getting flashed by every other car.
I also have a weird light pattern with the model 2 that I purchased.
I have also reached out to Kiwi Master and when I sent the attached picture they never replied.
I am returning the lights and will purchase the Oracle Oculus lights.
I do have the Kiwi master fog lights and am happy with them.

 

[El Zilcho]

So....after weeks of trying to get the lights adjusted, I can’t get them low enough without getting flashed by every other car.
I also have a weird light pattern with the model 2 that I purchased.
I have also reached out to Kiwi Master and when I sent the attached picture they never replied.
I am returning the lights and will purchase the Oracle Oculus lights.
I do have the Kiwi master fog lights and am happy with them.

Model 3 has better cutoff. I have a comparison somewhere in this thread.

 

[Pemberton325]

Model 3 has better cutoff. I have a comparison somewhere in this thread.

Thank you, I think I will save up and get the Oculas ones.

 

[Pemberton325]

Thank you, I think I will save up and get the Oculas ones.

Mai I finally got a reply from KiwiMaster. They are shipping meout a new set of the Model 3s. Will post an update when they arrive and I install them.

 

[SoCal]

Mai I finally got a reply from KiwiMaster. They are shipping meout a new set of the Model 3s. Will post an update when they arrive and I install them.

any updates?

I know the newest version has adjust screw, but out of stock on amazon store/

although Bunker Industries seems to have an identical headlight to the Kiwi

 

[ElvisJL]

any updates?

I know the newest version has adjust screw, but out of stock on amazon store/

although Bunker Industries seems to have an identical headlight to the Kiwi

I've been running my model 3's for nearly a year now and they've been good for the price and were superior over the stock halogen however, I plan on upgrading to either stock Rubi projectors with aftermarket bulbs or KC Gravity LED Pros. Haven't decided yet.

 

[Pemberton325]

any updates?

I know the newest version has adjust screw, but out of stock on amazon store/

although Bunker Industries seems to have an identical headlight to the Kiwi

Actually, Kiwi Master sent my replacement lights to the wrong address and would not re send them again. I ended up having to do a claim with Amazon to get my money back.

I ended up going with the Oracles and love them.

 

[SoCal]

installed the Kiwi's yesterday....loving them so far.

I tapped fuse 52(cigar lighter) for the halos....work great.

 

[Spearmin]

Only complaint is that they may bee too bright. I get flashed constantly when driving at night...

 

[jludave]

I get flashed constantly when driving at night...

If you're getting flashed, your headlights are not aimed properly.

 

[Spearmin]

If you're getting flashed, your headlights are not aimed properly.

I think your right about that. What method did you use?

 

[jludave]

What method did you use?

I no longer have the Kiwi Masters. However the general rule of thumb is to do the following:

1. Park the Jeep 15-20ft. away from a wall on a flat surface.
2. Measure from the ground to the center of each headlight.
3. Mark the same height on the wall with tape.
4. Aim the cutoff line to meet the marked spot on the wall.

If I remember correctly, the Kiwi Masters use washers and or springs on the bolts for adjustment.

 

[Spearmin]

I no longer have the Kiwi Masters. However the general rule of thumb is to do the following:

1. Park the Jeep 15-20ft. away from a wall on a flat surface.
2. Measure from the ground to the center of each headlight.
3. Mark the same height on the wall with tape.
4. Aim the cutoff line to meet the marked spot on the wall.

If I remember correctly, the Kiwi Masters use washers and or springs on the bolts for adjustment.

Thanks, maybe with will help stop from driving around with my hand on the hi-beam switch waiting to flash the next car back after they flash me...... Sooner or later I'm going to do this to a cop, that's not going to make him too happy.

Sponsored