Jeep 4XE Compatible Parts & Accessories

[GATORB8]

Has anyone added the Mopar Aux Switch kit? (P/N 82215798AE)

I'm worried about the PDC fitting between the firewall and the brake reservoir:

after seeing this post: https://www.jlwranglerforums.com/fo...ts-gauging-interest.73247/page-3#post-1566813

Yeah, I know I'm an idiot for not getting tow and thinking it'd be an easy add since I won't be towing with the Jeep.

Sponsored

 

[GGolds]

Come on you all - really want to know who has found the answer to a dead pedal. No modifications or fabrication needed. I had a Mountain Off-road dead pedal in my JK and it was amazing - who makes one with a perfect fit for the 4XE??

OK, I took the dead pedal I had on my 19 and then took a 2/2 inch metal corner bracket and mounted it to the dead pedal without the long metal piece that would attach to the bolt on the firewall. Attached one side to the pedal and the other side to the metal bracket on the LEFT SIDE of the inside wall of the Jeep, just inches from the firewall bolt. Now it works perfectly. Few.

 

[capn00]

Any pictures?

Very minor gaps on driver side mats near door sill, but better than I have experience in past vehicles with Weathertech previously. Integration of drains holes and utilizing factory drain plugs is great.

 

[bondijoe]

Can confirm 6CG99TZZAC does not fit on Sahara 4xe. 6CG99TZZAC headlight rings are a tad bit smaller and one of the tab holes is not the right size.

Just ordered 6KM36TZZAA, will update when it comes in. Plasti dipping the originals since I have them off now.

Just seeing if you tried to install 6KM36TZZAA on your 4xe and if it fit? Thanks!

 

[cutandrun]

After not liking the way Rancho’s RS9000 shocks fit on my stock height 4xe Rubicon, I was going to wait until manufacturer recommendations came down, but I was never good at patience. Last weekend I installed Fox 2.5 reservoir shocks all around and added the Fox ATS steering stabilizer while I was at it. Aside from the replacement axle bracket for the stabilizer needing some persuasion (a known issue), all went on easily. The Fox shocks are slightly longer than the Mopars. Ride is now completely adjustable.

 

[GATORB8]

Well, damn. Still waiting for the Jeep but just realized the License Plate relocation bracket I ordered for the rear Rugged Ridge HD bumper sits right in front of the rear 4xe badge. Anyone have a non-tire mounted relocation solution? Afraid the D ring mount brackets will interfere with the backup sensors.

 

[RNLROCK]

After not liking the way Rancho’s RS9000 shocks fit on my stock height 4xe Rubicon, I was going to wait until manufacturer recommendations came down, but I was never good at patience. Last weekend I installed Fox 2.5 reservoir shocks all around and added the Fox ATS steering stabilizer while I was at it. Aside from the replacement axle bracket for the stabilizer needing some persuasion (a known issue), all went on easily. The Fox shocks are slightly longer than the Mopars. Ride is now completely adjustable.

What was the issue with the Ranchos? Curious because I was thinking of getting them for my Sahara 4xe. Thanks.

 

[cutandrun]

What was the issue with the Ranchos? Curious because I was thinking of getting them for my Sahara 4xe. Thanks.

They were almost an inch shorter than the stock shocks. I did not want to lose any suspension travel. I also found the adjustment knob to be imprecise and difficult to set. I found this shock chart elsewhere on the forum. Very helpful (see the original thread for a link to the google doc https://www.jlwranglerforums.com/fo...gs-suspension-information-chart-matrix.66591/)

 

[Kayphix]

Sold my Jeep Wrangler 4xe due to changing circumstances. I needed a truck for work, so it had to go.
Located in Fort Collins/Denver area if anyone is interested. Feel free to PM for photos.

1) RockSlide Tailgate Table - $200 (paid $250) (Sold by Extreme Terrain) all hardware included.

2) Thinskins Rear door protectors. Unopened and in box
$130 (paid $142 w/ shipping)

3) Bulletproof phone mount for the 4xe - $50 (paid $60) brand new.

 

[tactical_gnr]

Sold my Jeep Wrangler 4xe due to changing circumstances. I needed a truck for work, so it had to go.
Located in Fort Collins/Denver area if anyone is interested. Feel free to PM for photos.

1) RockSlide Tailgate Table - $200 (paid $250) (Sold by Extreme Terrain) all hardware included.

2) Thinskins Rear door protectors. Unopened and in box
$130 (paid $142 w/ shipping)

3) Bulletproof phone mount for the 4xe - $50 (paid $60) brand new.

Long shot here, but you don’t happen to have the hardtop do you?

 

[nelson55917]

• Coyote Mirror for 2018-Current JL & JT (Pair) (Part No: MJL-800) - LINK (DOES NOT WORK)
  • Note: User “Sboden” reported that the charging port interferes with the mounting of these mirrors

I installed the Coyote Mirror above. The passenger side installs no issues at all. The driver side next to the charge port needs a small mod to the piece you screw on. The only reason the mount doesn't fit on the cowl is because the cowl seems to be a bit thicker metal around the charge port vs the passenger side. A simple cut to the lip and the piece goes on perfect. There is still a rigid edge on the bottom of the cowl that will prevent the coyote mirror holder from moving or slipping. Cutting the lip off took all of 30 seconds. Next time I pop the doors off I will shoot a pic. I would recommend, it is a simple mod with a washcloth to wrap the piece in a vice and a hand metal saw.

 

[Jocko]

Yes that is exactly the same mod I did to make my Coyotes work! It was super easy because they are made of aluminum! And because it still has the bottom part of the "lip" is stays stable and would still work fine if you ever want to install them on a non-4xe later.

 

[Awarner8]

I went the other route and trimmed the interior of the cowl. No change to the exterior so if they are ever removed it will be unnoticeable.

I can confirm the S&B CAI and functional hood scoops fit the rubicon 4xe.

 

[Jerpy]

I posted about this a couple weeks ago, but I figured it'd be worth a mention here: Diabolical is now taking pre-orders for their 4xe Slipstream Trunk Enclosure with the first run of deliveries scheduled for the end of this month. Perhaps @seannaz can add this to the first post?

 

[sdeli]

Has anyone found an engine skid plate that works with the Rubicon 4xe? I am looking at Rusty's JL Wrangler 2.0L Engine Skid (https://www.rustysoffroad.com/rustys-jl-wrangler-2l-engine-skid.html). They do not know if it works on the Rubicon 4xe.

Sponsored