Flush Mount Style LED Tail Lights for Jeep Wrangler JL

[Dyolfknip74]

What errors are you getting? I get the taillight out and hyper flash.

You need to fix that with JScan or a Tazer. That's the easier fix. I get BSM not working on start up.

Sponsored

 

[GH05T]

I don't get any errors at all but I programmed the Tazer for the lights as soon as they were installed. I did not drive with them installed without programming them with the Tazer.... but my BSM is not working at all either. I even toggled the BSM Off/On in the Tazer menu with a full reboot and 3 sleep cycles & BSM is still not working. Everything is tight. Everything else works, no errors/warnings, just the BSM is not working.

 

[Dyolfknip74]

I don't get any errors at all but I programmed the Tazer for the lights as soon as they were installed. I did not drive with them installed without programming them with the Tazer.... but my BSM is not working at all either. I even toggled the BSM Off/On in the Tazer menu & still not working. Everything is tight. Everything else works, no errors/warnings, just the BSM is not working.

Yep. Same boat. Did you reseat connectors as well?

 

[GH05T]

Yep. Same boat. Did you reseat connectors as well?

Don't need to re-seat them because I made damn sure they were VERY tight, clicked in, & lockers locked down when I initially installed them last night.

I'm going to try to reprogram for the tail lights again while simultaneously reprogramming the BSM within the Tazer so it's all done at the same time within the Tazer & see if that works as a fix.

 

[Dyolfknip74]

Don't need to re-seat them because I made damn sure they were VERY tight, clicked in, & lockers locked down when I initially installed them last night.

I'm going to try to reprogram for the tail lights again while simultaneously reprogramming the BSM within the Tazer so it's all done at the same time within the Tazer & see if that works as a fix.

I tried that with JScan today. Didn't help.

 

[Dyolfknip74]

Don't need to re-seat them because I made damn sure they were VERY tight, clicked in, & lockers locked down when I initially installed them last night.

I'm going to try to reprogram for the tail lights again while simultaneously reprogramming the BSM within the Tazer so it's all done at the same time within the Tazer & see if that works as a fix.

There is a post somewhere where @JP_Oracle gave someone tips on how to correct the bad BSM connection but OP didn't go into detail.

 

[Crusifix]

Mine just arrived

 

[Jjirish]

Mine arrived... but ofcourse it's raining so I'm not installing... grrr

 

[TX_Ovrlnd]

Mine arrived... but of course it's raining so I'm not installing... grrr

Badass letting a little rain scare her away!

 

[Jjirish]

Badass letting a little rain scare her away!

Ms. Badass likes the attention she gets installing things in the sunshine.

 

[Dyolfknip74]

Ms. Badass likes the attention she gets installing things in the sunshine.

Pics or it didn't happen!

 

[Jjirish]

Pics or it didn't happen!

I'm taking that as a challenge!

 

[Dyolfknip74]

I'm taking that as a challenge!

Uhg, if you have to, I suppose we can allow that. I guess.

 

[BullMoose1776]

Been following this thread for a while...but I have a few questions.

Does everyone have the issues with these lights?

Is the issue ever going to be resolved without a TazerJL or JScan?

 

[weeitsmikelee]

Halogens are fine.
OEM leds are ok w programmers.
OEM leds w/ bsm are less ok.
No non-programmer fix yet.

Been following this thread for a while...but I have a few questions.

Does everyone have the issues with these lights?

Is the issue ever going to be resolved without a TazerJL or JScan?

Sponsored