First aftermarket JL LED Tailights

[Brooklynjlu2018]

Now if i have factory led package do i still need the load resistors with these

Advertisement

 

[johnparjr]

Yep

 

[Wrangler847]

I had no clue what to do with those and just kept em away from wires when I put em in.

 

[Brooklynjlu2018]

Anyone elses say tail lights out after installation i had factory leds

 

[WalkingJL]

Has anybody tried the sequential taillight? I just installed them and the sequential turn signal doesn't work, but brake lights are acting as the turn signal.

These:https://www.ebay.com/itm/LED-Sequen...18-UP-W-Full-LED-DRL-/123921292356?nav=SEARCH

 

[Brooklynjlu2018]

Just ordered these sequential led taillights. 300$ shipped supposedly have the blind spot monitoring and no error message for those of us who have the factory led package because those other ones that everyone is using did not work in my jeep because i had the factory led package

 

[Brooklynjlu2018]

just found this as well

Just ordered these sequential led taillights. 300$ shipped supposedly have the blind spot monitoring and no error message for those of us who have the factory led package because those other ones that everyone is using did not work in my jeep because i had the factory led package

 

[blnewt]

Should start a new thread " Second LED tails available"
look forward to reviews on them, FWIW mine are still working superb!

 

[Du0377]

Smoked looks great, but will these aftermarket tail lights work on JLs with LED pkg? Any issue with the BSM?

Hey I know this is old, but with the led package you wouldn’t need a resistor because you are already drawing less power. The resistor is wired in parallel with the circuit. If you just cut out the resistor and install you would be fine. The resistor is there to essentially trick the jeep into thinking the halogens are still installed and you don’t get a hyper-blink in the cabin.

 

[wyobob44]

Hey I know this is old, but with the led package you wouldn’t need a resistor because you are already drawing less power. The resistor is wired in parallel with the circuit. If you just cut out the resistor and install you would be fine. The resistor is there to essentially trick the jeep into thinking the halogens are still installed and you don’t get a hyper-blink in the cabin.

I just installed a set in my JLUR that came with Factory LED and i get the message on the dash Turn Signal Lights Out, hyper flashing on turn indicators on dash, but both lights outside blink at proper rate.
So i just cut out the resistor and cap off the wires??

 

[blnewt]

Looks like you can get them for under $100 now.
https://www.aliexpress.com/item/33002804197.html
FWIW these lights are a great addition to non LED JLs, have had nothing but positive comments and they have performed flawlessly. Only two caveats, the reverse LED isn't very bright (same complaint as the stock reverse light for those JLs w/ the factory LED set). And the gloss lens cover needs to be cleaned w/a very soft microfiber cloth as it's easy to scratch (but can be buffed shiny again). So I would recommend a reverse light bar such as this~
https://www.jlwranglerforums.com/fo...t-bar-on-jl-sport-plastic-bumper-cover.31728/

 

[Wrangler847]

I've had mine on since July and they are going strong. Love them

 

[lanman08]

Has anyone found any aftermarket lights like the smoked ones mentioned in this thread without smoke covering/ie like the factory? If so where did you get them

 

[sheogorath]

Has anyone found any aftermarket lights like the smoked ones mentioned in this thread without smoke covering/ie like the factory? If so where did you get them

You can finde the non smoked European style on aliexpress

 

[ChattVol]

You can finde the non smoked European style on aliexpress

I searched and only found smoked LED style...Link?