Sponsored

Anybody running Ultimate Dana 60's yet?

Status
Not open for further replies.

texastonka

Well-Known Member
First Name
Kurt
Joined
Oct 28, 2018
Threads
6
Messages
48
Reaction score
16
Location
Texas
Vehicle(s)
Jeep Trackhawk, AEV Prospector XL, Viper TA2.0, Dodge Demon, etc etc etc...
Current status.

IMG_20190228_173212_573.jpg
XD60 at 72”? 5” BS wheel?

What is outside to outside measurements from OS tire to OS tire? Looking for new trailer and need width info for that. Thanks.
Sponsored

 

texastonka

Well-Known Member
First Name
Kurt
Joined
Oct 28, 2018
Threads
6
Messages
48
Reaction score
16
Location
Texas
Vehicle(s)
Jeep Trackhawk, AEV Prospector XL, Viper TA2.0, Dodge Demon, etc etc etc...
It cannot be wired into the factory canbus system. I just installed the prorock 44 frontvand have to wire to a switch. The factory is a canbus system. I’ve spoken to engineers at FCA and it’s not a thing
There has got to be a way. We’ve broken into the canbus for so many other things.
Just will take someone much smarter than me and possibly an engineer at FCA to take a few bucks under the table.
 
OP
OP
DOOKEY

DOOKEY

Well-Known Member
First Name
Andy
Joined
Mar 26, 2018
Threads
54
Messages
2,288
Reaction score
5,180
Location
Thornton, CO
Website
www.tractionoffroad.com
Vehicle(s)
2021 GCM 392 - 2019 SG JLUR
Occupation
Wheel Pimp.
XD60 at 72”? 5” BS wheel?

What is outside to outside measurements from OS tire to OS tire? Looking for new trailer and need width info for that. Thanks.
72.5" axles. 4.5" back spacing. 6.5" front spacing. 85.5" outside to outside plus tire bulge.
 
OP
OP
DOOKEY

DOOKEY

Well-Known Member
First Name
Andy
Joined
Mar 26, 2018
Threads
54
Messages
2,288
Reaction score
5,180
Location
Thornton, CO
Website
www.tractionoffroad.com
Vehicle(s)
2021 GCM 392 - 2019 SG JLUR
Occupation
Wheel Pimp.
There has got to be a way. We’ve broken into the canbus for so many other things.
Just will take someone much smarter than me and possibly an engineer at FCA to take a few bucks under the table.
We'll get it taken care of.
 

texastonka

Well-Known Member
First Name
Kurt
Joined
Oct 28, 2018
Threads
6
Messages
48
Reaction score
16
Location
Texas
Vehicle(s)
Jeep Trackhawk, AEV Prospector XL, Viper TA2.0, Dodge Demon, etc etc etc...
72.5" axles. 4.5" back spacing. 6.5" front spacing. 85.5" outside to outside plus tire bulge.
Need more info on the wheels. 11” wide sounds awesome.
 

Sponsored

OP
OP
DOOKEY

DOOKEY

Well-Known Member
First Name
Andy
Joined
Mar 26, 2018
Threads
54
Messages
2,288
Reaction score
5,180
Location
Thornton, CO
Website
www.tractionoffroad.com
Vehicle(s)
2021 GCM 392 - 2019 SG JLUR
Occupation
Wheel Pimp.

texastonka

Well-Known Member
First Name
Kurt
Joined
Oct 28, 2018
Threads
6
Messages
48
Reaction score
16
Location
Texas
Vehicle(s)
Jeep Trackhawk, AEV Prospector XL, Viper TA2.0, Dodge Demon, etc etc etc...
They're my wheels. They are 10" wide bead seat but 11" wide over all.
Nice! That's how I'd love to have a set of Forged Trail Ready beadlocks with rock rings made.
 

Lorenc

Well-Known Member
First Name
Loren
Joined
Mar 22, 2019
Threads
15
Messages
87
Reaction score
79
Location
Palm Desert
Vehicle(s)
2019 JL Rubicon
Occupation
Retired
Vehicle Showcase
1
72.5" axles. 4.5" back spacing. 6.5" front spacing. 85.5" outside to outside plus tire bulge.
I've been reading your posts on the Ultimate 60 upgrade, and am particularly concerned about my overall width to get it in my garage (94" opening".
It looks like you have Toyo 40s, which I know bulge out a little more than the Nittos I'm doing (according to tire spec the Toyo is 14.4" and the Nitto is 13.58") Would you mind telling me what the overall width is with the bulge?
FYI, I'm planning on using 4" backspacing and 9" wheels with it.

Thanks so much!

Loren
 

Sponsored

Lorenc

Well-Known Member
First Name
Loren
Joined
Mar 22, 2019
Threads
15
Messages
87
Reaction score
79
Location
Palm Desert
Vehicle(s)
2019 JL Rubicon
Occupation
Retired
Vehicle Showcase
1
9" wide wheels will change the bulge amount a bit. I'm 1-3/8" max with 10".

20190323_201458.jpg
Andy, we're almost done with our build. We put in the Ultimate 60s and are using a Tazer J Mini, which I think is what you're using. Did you have to do something to turn off the Service 4x4 System light on Instrument panel?

This is what we've done so far....
  • We made sure 11.01 was the current updated Firmware in Tazer
  • Set Locker to Both-is this correct position to remove the factory E Lockers?
  • Set Front Axle Disconnect to Yes-is this the correct setting?
  • There is another Menu item after that for DTCM, what is this and does it need to be changed?
Thanks

Loren
 

5280Sapper

Well-Known Member
First Name
Michael
Joined
May 13, 2018
Threads
15
Messages
339
Reaction score
473
Location
Saratoga Springs, Utah
Vehicle(s)
2018 JLU Rubicon
Occupation
Disabled Veteran
Factory lockers off. Factory axle disconnect off, change gear ratio and tire size .. should work after that

Andy, we're almost done with our build. We put in the Ultimate 60s and are using a Tazer J Mini, which I think is what you're using. Did you have to do something to turn off the Service 4x4 System light on Instrument panel?

This is what we've done so far....
  • We made sure 11.01 was the current updated Firmware in Tazer
  • Set Locker to Both-is this correct position to remove the factory E Lockers?
  • Set Front Axle Disconnect to Yes-is this the correct setting?
  • There is another Menu item after that for DTCM, what is this and does it need to be changed?
Thanks

Loren
 
OP
OP
DOOKEY

DOOKEY

Well-Known Member
First Name
Andy
Joined
Mar 26, 2018
Threads
54
Messages
2,288
Reaction score
5,180
Location
Thornton, CO
Website
www.tractionoffroad.com
Vehicle(s)
2021 GCM 392 - 2019 SG JLUR
Occupation
Wheel Pimp.
Andy, we're almost done with our build. We put in the Ultimate 60s and are using a Tazer J Mini, which I think is what you're using. Did you have to do something to turn off the Service 4x4 System light on Instrument panel?

This is what we've done so far....
  • We made sure 11.01 was the current updated Firmware in Tazer
  • Set Locker to Both-is this correct position to remove the factory E Lockers?
  • Set Front Axle Disconnect to Yes-is this the correct setting?
  • There is another Menu item after that for DTCM, what is this and does it need to be changed?
Thanks

Loren
I'm not helping unless you post pics.
Sponsored

 
Status
Not open for further replies.
 



Top