Search results

Any suggestions for high clearance (at least 7’) parking garages in downtown DC? I see enough Jeeps around……

Received an email from Jeep.mopar.com stating that I had a low oil pressure warning (and the fuel pump recall…). Odd thing is that the Jeep wasn’t running anytime near when the email was sent, and certainly didn’t have any warnings earlier in the day. Moreover the vehicle health status in the...

Made some adapters to let me use either battery clips or a cigarette lighter for powering my small air compressor. Of course I bought the 12V male plug off Amazon, and of course it’s a POS that doesn’t seat well, and so tends to get hot due to increased resistance….you know where this is going...

More miles per neutron!! https://oilprice.com/Alternative-Energy/Nuclear-Power/Nuclear-Diesel-Could-Become-A-Gamechanger-In-Energy-Markets.amp.html

Has anyone successfully refilled one of the 16oz measure & pour EDT bottles? I’m getting ready to order a gallon of EDT and was hoping to just keep using the 16 oz bottle on road trips, then realized it’s a single opening (unlike the archoil container that has a separate filler cap).

Probably here in the forums someplace, but… to make your life much easier when draining water from the fuel filter housing buy a few inches of 5/16” fuel injection hose. It fits perfectly over the outlet nub and lets you drain the housing without removing the armor. just don’t forget to prime...

Just wondering if the lift-mate is compatible with the stock 17” rubicon wheels. Need an interim solution for jacking until I get a bumper w/ high-lift slots in it…..

Has anyone tried these things...they're a pair of aluminum molle(ish?) plates that mount on the inside of the rear side windows. Would give me something to tie additional gear to, but i'm worried about interference with my XG gama bags...

Started making a 3D printed clip to hold my CB mic on the passenger handle, then changed my mind and designed it to fasten to the console w/ adhesive (VHB). I had already gone through the trouble of making a thermoplastic impression of the handle and a rough bracket design based on that and...

Just thinking it might be nice to have a dedicated forum or subforum for 3D printed parts discussions.

This should click into the rails on the side of the driver's seat (between that and the door). Fits my D-cell maglite fine, but I'm not 100% happy with how well it stays in place in the vehicle so posting the zipped f3d model for folks to play with. By the way, Is there a way to request a...

Does anyone know if the aux battery is required for the factory remote start feature? Thanks!

Ordered the 6 can kit from woolwaxusa, and finally got around to applying it this afternoon. it was a pretty easy job, even without a lift or removing the wheels. Did have a bit of drama with the extension hose (not the wand...that worked fine), as it didn't want to stay on the can and tended...

Seems to me that a better way to facilitate removing the doors would be to have a removable pin in the door check (yellow arrow on attached photo). Has anyone tried this and/or is anyone aware of a drop-in replacement? That said, managed without a door check in my YJ for decades....that's...

Has anyone figured out a way to separate the reading/map light functions from the dome light? I’m putting red leds in the dome lights but would like to keep the option to use the smaller white lights.

Has anyone removed their fuel fill housing? It is just clipped in so can be pried out using a trim tool to release the clips but unlike the fuel hose the DEF hose is apparently bolted to the housing. I suspect you need to remove the taillight to access those bolts but was wondering if anyone...

So something hit my gorilla glass windshield (or hit my windshield wiper, which then hit the windshield...not exactly sure because i didn't see it happen) and the cracks immediately went all the way across. Tried putting in a warranty claim which was denied....although my reading was that it...

Wonder if folks have had experience with any rustproofing shops/services in Maryland, preferably in central MD. Wanting to get ahead of the winter salt season and don't have a good spot to do fluid film, etc. myself.

Probably pissing in the wind, but have folks thought about trying to lobby the National Park Service for an ORV permit that would be good across the US at USG controlled ORV areas? It kinda sucks having to buy multiple short term passes if a single annual pass could be implemented....

Sticking this here as it applies to a few different situations (mods feel free to move!)... I did some searching and wasn't able to find much on running wiring -across- the engine bay. I'm wondering what people's experiences and opinions are. As I see it you can run something under the trim...