Ok this is weird.
21 Rubicon 2 door, 13,500 miles. Tracks arrow straight.
2.5" MC GC lift on BFG MTs in a 315/70/17 size
Cro Mo axle shafts, Artec trusses and American Iron Ball Joint Deletes in Cast Iron Mojave Knuckles
All nuts and bolts have been torqued and paint marked.
In the past...
Short version, reverse sensors are not working. How do I reset them.
Long version, 21 Rubi had major issues on the trail and lost power steering, front camera, swaybar disco, FAD and rear sensors. Even broke driver side CV joint. Got it off the trail and as I drove back to camp everything came...
Does anyone know….
If I pull the FAD actuator and fork off the axle and then put tge jeep in 4wd and back to 2wd while parked, will the fork move back and forth or does it need to be rolling?
TIA
Got stuck and high centered. Pulled it off and lost all of the above. Spent six hours winching a one wheel drive out of the gnar. Once we got to a place where I could drive it home, all of those systems came back.
Full skids no broken wires
21 Rubi 2dr AT 2.0T
Still have a CEL that I will...
Today is 1/17/23 and the "next available appointment" for my jeep is 3/28/23.
Not a big deal to me at all as they just need to add Loctite to the two water pump bolts. It's not leaking and totally drivable. But it seems like every dealer is buried with too much service work and not enough...
Trying to replace my drag link and I can not get the ball joint to pop loose from the pitman arm. 21 Rubicon with less than 8,000 miles.
So far I have tried.
Manual Pickle Fork and hammer.
Heat from Propane Torch and Manual Pickle Fork
Hammering on the Pitman Arm while Pickle Fork was wedged...
Expert - as in you are or were involved in the design and testing of suspension components and lift kits for the JL? I have a couple of specific questions I would like to PM about.
TIA
Anyone install metal or steel fender flares and then regret doing so later?
I know the plastic ones, both factory and aftermarket, are designed to mount with plastic pins and pop off if you bump something. The metal ones that I have seen are all bolted solid to the tub. I prefer the looks of...
I have been carrying a Leatherman Wingman on all of my trips for the past 18 months or so and I find I need it for something on almost every trip. For example, the last two weeks I have used it to repair two lighted flag poles for different people. I've also used it to cut and re-apply zip...
So I was playing with my factory installed Homelink and looking at the visor and noticed, there are no wires. Is this thing hardwired? If so, where are they or how are they routed? If not how long does the battery last?
TIA
Hi, Im looking to order some KC Flex Era 4 lights and I would like to use the included KC switch. Does anyone know if it is possible to mount this switch below the factory headlight knob and above the driver side lower speaker?
Is there room back there?
Hey all,
I would love to see the what, where and how you have mounted your rear chase lights.
What lights did you use?
What bracket? If you fabbed it yourself can you please post photos of that as well?
How did you run the wiringing? Under the rig or through the cab?
Thank you.
And what did you replace it with?
1)
I have a 2 dr and I broke the little plastic clip in the driver side seat rail that "remembers" you seat position. It locked my seat in the full forward position. I was able to unlock it so that I could drive. I replaced it with another factory clip and...
Hi All,
What is the general consensus or thoughts on running larger tires on BUILT factory D44s? Built as in Artec Truss Front and rear, RCV Axles front and rear, Reid Racing Knuckles, HD Ball Joints or Ball Joint Eliminators, HD TireRod, Ends and Pitman Arm, 5.13:1 Gears but keeping all of...
The frame of the soft top bolts to the upper rear portion of the roll cage with two bolts on each side.
Does anyone know the size and thread pitch of these bolts?
I have a hard top but would like to mount something using the threaded lugs where the soft top frame mounts but I do not know what...
I'm researching fenders and I would like to know your experiences and opinions on metal vs plastic.
I really like the looks of the metal fenders from Nemisis and Motobilt and even MC. But I'm a bit concerned that if I bump or lean on a rock, not only will the metal fender bend but it might...
Howdy Folks,
I'd be interested to hear about any negative experiences you may have had with different control arms and /or joints. Too much maintenance? Too short of a service life? To expensive to replace? Too noisy? Too weak? Too hard or complicated to service?
Basically, based on personal...
Part number 6BM40TX7AC is for the large interior plastic panel on the 2018-2022 JL Swing gate. I need just the smaller upper plastic insert that says Jeep on it but I can not find it.
And the clips to install it.
Thank you.