Search results

Back to Back In Black Traded my 2020 Black Willys for 2021 Black Rubicon 4xe Willys 14 mpg - 4xe 30 mpg plus (still climbing!) NoBrainer!

Back in July - Traded my 2020 Willys for 2021 Rubicon 4xe Added Mopar Steel Bumper, Mopar Performance Rockrails, and All Black Rims! Willys 14 mpg 4xe 32 mpg plus! No brainer!

None - Brand New - Meguiars “Ultimate Wash and Wax” car wash

❤ My 2020 Willys! Equipped with Technology Pkg, Safety Pkg, Tow Pkg, Hard Top, and Sun Rider Bonnet. Added Mopar Cold Air Intake, Mopar Front Steel Bumper, Spash Guard, Winch Bar, Mopar Homelink Visor (pwr to aux switches), Mopar Sill Plates, Mopar Grab Handles, 15” Rubber Antenna, Oracle...

I paid $175 from a jeep dealer including shipping, so anything less than that would be a bargain! check ebay you may be surprised to find one there for a steal.

My 2020 JLU hardtop tinted windows... - AC is having issues on long trips here in FLA. Around town I’m amazed how ice cold it gets no Matter how hot the temp is. On long highway trips It seems to become intermittent - About 45 min - 1hr Hwy speeds the cabin begins to heat up while cold air is...

My Visor finally arrived, took 2 weeks to deliver within state! (I guess no more pony-express). Anyway, dove back in and attacked the removal of the gray pin from the BCM plug - finally "success!" I was using the back end and trying to pull the pin out, usually works on a round pin. However this...

Did you have the dealer enter a flash code to get it to work or was it simply plug and play?

How much does it cost? Does not state cost or how to order - only requires inquiry.

Took the Jeep to the dealer today, apparently the BCM plug was loose. All good now - going to continue the install when the Mopar visor w/Homelink arrives. Fingers crossed

Gave up on unpinning - going to use solder-less connectors, don't even have the homelink visor yet I was trying to have the prep work in place before it gets here tomorrow. However after calling it a day, with no alterations - I'm having a strange phenomenon - after I reinserted the plug into...

Thanks! Is there a special technique to remove the pin with the tool? because I'm not having any luck

Added the MOPAR Cold Air Intake to my 2020 Wrangler Willys Edition - With the vent open - its definitely much more throaty and responsive. No effect at low RPM - Gotta Rev and Go - Higher the Revs the Sweeter it Sounds! When the Vent is Closed can hear a slight difference but not like when its...

OK found the gray wire - Disconnected the harness from the kick panel BCM. What did you use to unpin the wire, I have a depinning extraction tool and I cannot get it to budge.

"I did not think to take pics while doing it because I was in problem solving mode and went into the situation hoping it would be just plug and play. These are the pics of the connector, the wire that I de-pinned out of the connector and the green jumper wire I made to connect to the switched...

I just purchased the kit from the dealer, however I’m hesitant to install the vent due to the warning on the box. Why would it have this crazy warning If they are being sold And installed as a factory option?

Added the MOPAR Cold Air Intake to my 2020 Wrangler Willys Edition - With the vent open - its definitely much more throaty and responsive. No effect at low RPM - Gotta Rev and Go - Higher the Revs the Sweeter it Sounds! When the Vent is Closed can hear a slight difference but not like when its...

I purchased the Mopar Cold Intake a few weeks ago however I’m somewhat concerned with the warning on the box. Are you happy with the install? Do you notice see/hear/feel difference with the cutout? Your thoughts would be very helpful before I cut my hood. Thanks

Thanks, this helps a lot!