Search results

I'm getting ready to do my ball joints and have access to a garage lift buts it's a narrow garage. Now I'm concerned the passenger side axle shaft may be too long and will hit the garage wall. Am I correct I'm assuming I only have to pull the axle from the FAD out and not the whole thing? Does...

This is only the second set of ball joints I've purchased so I'm not sure if this is normal or not. Two of the four have some play in them, I'd say an 1/8 inch, very small but noticable compared to the other two which are solid. I thought when they are new they wouldn't move at all by hand. I...

Please look at the pics and if you have a question let me know. No trades and willing to meet at short distance. The bumper was removed at 12k miles, the Driveshaft at 10k and the stabilizer has less than 1k miles on it Front Driveshaft $125/obo Metalcloak front stabilizer $50 Ironman 4X4 class...

I'm selling the stock steel rear bumper with the end caps and tow hook from my 2018 JLUR with 12k miles. It's in good shape, I'll send pics to anyone interested. I'm cutting the wiring harness to use on my new bumper. I would prefer local pick up. $250

Does anyone have any experience with these bumpers? https://ironman4x4america.com/raid-rear-bumper-kit-suited-for-jeep-wrangler-jl/

I bought this as part of a steering and suspension upgrade for my Jeep Wrangler JL and ended up going another route. This shock has only been on for about 1000 miles and is like new. It does not come with the hardware in the the stock photo above, it is just the shock and boot. I ran this shock...

I had a Cobra 75 with a Firestik mounted to my tire carrier on my JKUR and it worked pretty well. I now have a JL and decided to try out the Midland 75-822 cb and I'm looking at different mounting options. I like the 75-822 because it is small and can be used as a handheld. The only thing I use...

I tried to put this in the exhaust thread but it said I wasn't allowed to post there. I was under the rear of my Jeep doing the sensor potting this weekend and noticed that the heat shield over the muffler was actually laying on top of the muffler. All 7-8 nuts that hold the heat shield against...

I'm installing a MC dual rate lift with the shocks, new drive shaft and the tie rod/ drag link upgrade. I've got a little money left over and I'm curious if I should buy the front lca's or rear? I'm going to be using it on moderate trails, mostly rock crawling and I want to get the most bang for...

Installing a new lift and looking to sell the stock Rubicon suspension. Currently have 9700 miles on it and it is scheduled to be swapped out on March 26th in Topeka. I live in Wichita but would love to find someone to sell it to there so I don't have to haul it back. This will be springs...

We just made a 7 hour drive to Denver and the temps outside during the drive were -2 to 2F the entire way. My wife and I noticed that on both sides right around where the front doors latch there was a lot of cold air coming through. Enough that you couldn't keep your arm on the armrest for...

I've got a tazer lite for my 2018 Jeep Wrangler JL. I've taken it in and out a couple of times when I've got the vehicle serviced at the dealership so I'm familiar with how to marry it and unmarry it. Today when I went to take it out so the dealership could work on the vehicle it would not give...

Got home from a road trip and found this lying on the driver's side floorboard... I pulled off the kick panel and looked around but couldn't see anywhere obvious that it went. Any ideas?

I installed the OME lift in my JKUR 10 years ago but don't have the room and have no interest in installing a 2.5" MC lift on my JKUR this time. Can anyone recommend a reputable shop within a couple of hours if wichita that can do it? What's a reasonable price for an install?

I'm located in the midwest but will to pay reasonable shipping for anyone trying to sell a Mopar Grill and Winch guard for the factory steel bumper package.

I'm looking at the Quadratec aluminum full width rear bumper, does anyone have any experience with it? I had a Rugged Ridge XHD on my JKUR and really liked it but I was looking to shave some weight with my new bumper. I like the looks of both the RR and Quadratec but want something that can take...

At the end of May 2020 I was messing with the amber side marker light on my 2018 JLUR and ended up losing the T30 screw that holds it in place. I went online to buy a replacement but couldn't find it anywhere. Ultimately I went to two different local dealerships three different times and could...

I was replacing my driver's side front marker light and lost the torx screw. The video's I have watched say it's a t-30. I went to the dealership and they have no idea what size it is and the parts guy couldn't find a schematic showing the screw. He watched the video with me so he knew what I...