Hi,
I recall having seen some fixes for windshield visors that were based upon aftermarket new-and-improved bracket parts.
At the time, my visors were fine, so I did not pay close attention, but I finally heard a snap on the driver-side visor, and now it hangs loosely when I rotate it...
Hi,
It had not occurred to me that the form-fitting heat shields supplied with the Group 48 / H6 batteries would not be a good fit for the longer Group 94 / H7 batteries.
Has anyone found out the part number for the heat shields that MOPAR uses on any of their vehicles ( perhaps some RAM...
Hi,
Batteries sized as Group 48 / H6 or Group 94 / H7 will both fit in the Wrangler battery bucket, but many parts vendor websites post a note that the Group 48 / H6 are for 2018+ Wranglers with Start/Stop while the Group 94 / H7 batteries are for 2018+ Wranglers without Start/Stop.
I...
Hi,
The DIY tutorial videos make it look easy to disconnect the wiring for the lights in the front fenders. You just pull the red tab back and slide the connector out.
Well, I pulled the red tab back, and the connector was still stuck firmly in place, so I pulled the red tab again, and the...
Hi,
Next week, I am going to pull a fender on my 2020 JLUR, and I am wondering what the worst-case, break-em-all fender clip count might be so I can prepare accordingly.
I searched and found a few threads with the same question that linked to a few 20-page TLDR threads that did not answer the...
Hi,
I am wondering why some manufacturers of skid plates suggest that there is a significant difference between the original M210 Rubicon axle with the differential fluid drain plug, and the newer M210 Rubicon axle without the differential fluid drain plug.
Is the shape of the differential...
Hi,
There are several brackets made to raise the axle mount of the rear track bar.
Are there any brackets made to lower the mount on the frame?
I have been looking at the clearance under the rear passenger quadrant and it seems like the nearest conflict might be the rear sway bar. I am...
Has anyone seen any real life reviews of Snatch Blocks?
Almost everything I have found is an affiliate link copy-paste of whatever the manufacturers' catalog did or did not describe.
Fun facts:
The countersunk lug nut hole in Mickey Thompson Classic III is 1.100" in diameter.
3/4" or 19mm thin wall sockets fit and work OK.
13/16" or 21mm thin wall sockets may just fit but are impractical to use.
Gorilla 41147 retail for 3/4" or 19mm socket
Gorilla 41148 bulk for 3/4" or...
Hi,
I searched and came up empty.
How do you remove the engine coolant reservoir cap on a 2020 3.6L ESS Wrangler JLUR?
I found some info about 2018-2019 JL caps that have a tab and a key notch. My JEEP doesn't have that sort of notched tab.
I can back the cap counterclockwise several...
Hi,
I feel a bit dumb asking the question, but want to ask; is there a definitive MOPAR part number for the Wrangler JL power steering fluid?
I have a 2020 Wrangler JLUR 3.6L non E-torque Jeep.
The owners manual says:
"We recommend you use MOPAR Electric Steering Pump Fluid".
I want to...
Hi,
I am wondering if someone makes a small plastic or rubber widget meant to serve as a rope thimble cover for winch lines.
Something like the orange thing sketched in the pictures shown here:
Ideally it would be simple injection molded thing-a-ma-jig. It would not be too expensive. It...
I have a pair of brand new open box MORryde Jeep 2018+ Wrangler JL Rotopax Fuel Can Side Mounts.
I purchased these as part of the MORryde fuel can holder packages so that I could use the fuel can holders in a custom rack assembly. These side mounts have never been mounted, used, etc. I opened...
ROCK HARD 4X4™ ROCK RACK CARGO BASKET [RH-2004]
Local pick up only.
I purchased this last year to get a good look at it and to consider using as part of our camping set up. I installed it and drove around with it for a few miles but decided I wanted to weld up a custom gear rack so I took it...
Hi,
This morning I attempted to install a Zeon 10-S on my 3.6L ESS 2020 JLU Rubicon. My bumper has the popular lowered winch mount feature so the winch is intended to fit between the frames and the front brackets.
Try as I might I could not get the winch in between the ears of the frame...
Hi,
Are the Mopar 06511076AA M10 Bracket to Frame Rivnut Nutserts removable and reusable or are they more or less permanently wedged into your frame after an initial tightening of the bolt that threads in to them?
https://www.quadratec.com/p/mopar/front-lower-skid-plate-nutsert-jl-06511076AA...
Hi,
I have a question about the OEM skid plate brackets.
On my 2020 JLU Rubicon, that came equipped with factory steel bumpers, the lower edge of the front skid plate is attached to the frame with two small skid plate brackets.
Skid Plate Bracket, Right
68353836AB
Skid Plate Bracket, Left...