Received my Rock Krawler adjustable upper control arms for my 18 JLUR, has Mopar lift, but already replaced isolators with USA Alloys, replaced track bar with Rock Krawler adjustable, replaced damper with Falcon 2.2 adjustable, but would like to add about a degree of caster, so adding these...
After installing my Mopar lift I have a severe lean to the right. Fuel doesn't matter much. I mean c'mon when my 235 ass sits down it would offset fuel and it doesn't.
Yes everything is installed correctly and to spec. I wonder though as it has been pointed out where the Mopar instructions have...
Tip for anyone thinking of ordering these, part no. 61003 for Mopar lift kit. Don't. I have two sets and both LH pads are wrong. USA Alloy nicely sent me a replacement set, but that was wrong. I read somewhere about these being wrong. They have contacted me on helping them figure it out but I...
Hey experts or anyone with factory JL Rubi rear spring isolators laying around, what is the exact outer dimension of the isolator and the inner hole dimension? thanks
I am leaning to the right appx 3/8-1/2". I have the Mopar lift. I retorqued the entire suspension, it may have helped a 1/8".
It appears as if the lean is coming from the RH rear spring. As if I lift that only a little it will also lift and transfer weight to the LH front, technically leveling...
I have an 18 Rubi Unlimited, wandered from the beginning, not horrible, but bad enough that you could not look away.
I have installed numerous adds but let's focus on the suspension. The main issue from delivery was about a 1/4" to 1/2" play in the steering wheel, not as bad as some, but as...
Is caster angles different on LH vs RH because the axle yokes are just built not quite even on both sides?
Or because of the way the frames are not welded up square and true?
I want to use brackets mainly for ride, but am afraid I still need some fine tuning to get both sides similar with...
So now I noticed and took measurements on my 18 JL Rubicon 4dr after installing the Mopar lift that I am exactly 3/8" lower on the passenger side front and rear.
Any ideas on why? It's fairly noticeable when parked and when I drive. This pisses me off because I can tell that 3/8". You wouldn't...
So I put 35/12.5/17's on before any lift. After the tires my 18 JLUR almost drove normal with minor wandering compared to the stock tires and rims. Then I installed the Mopar very meticulously and checked everything with toe in almost perfect and the wandering is back. I don't know how to...
So while Max 3 products seem extremely well made, they are not lining up to well. I have the winch plate and no way in hell is it going on unless I either grind the hell out of the winch plate or ream the hole in the frame (not preferred). Then whatever the plates are on the bottom of the frame...
By the way, first Jeep ever owned and first build ever done. Being 60 though I have turned a lot of wrenches and fixed a lot of equipment, regardless bought the lifetime warranty today, you never know.
Well finally I have all the components together. I didn't drive it much until I settled on...
Hello builders, what's the best video you have seen to help install the Mopar 2" lift on a JLUR? I need to get this done, but the instructions are not the best to interpret. Thanks, links if you have.
Anyone buy and install this winch yet?
If so, what is your impression of it in all aspects.
To be honest, I think it looks great which is driving me to buy it over Smitty or Warn VR8, and budget.
So after reading numerous posts about the Rubicon Unlimited factory springs being set by the package ordered. Which I have the tow group, hard top, steel bumper package and numerous have said the factory springs are installed to accommodate these features.
My question is if the springs are...
Maybe this has been posted, if so, don't have a cow. This is the best video I have seen on the steering issue. This needs to be under recall by Jeep. Obviously there were several issues, not just the box.
Hello, I have not removed the rear camera yet, but what's to prevent a thief from just unscrewing it and taking it? Anyone have a secure method to prevent that?
Ordered 8/14, and the tracking system here says it's completed. Sticker was emailed to me. Does this mean it is built and ready to ship?
I cannot believe it, was prepped for 8 weeks or more. But hey, bring it!!
I ordered last Monday the 13th, had my VON day one, then VIN a few days later and salesman said status was D1. So what do the experts think I am looking at timewise? Sorry I scoured posts and it gets overwhelming trying to figure out the averages for most posters. Thanks.