Search results

  1. What did you do TO your Jeep JL today?

    man, those things look soooooo siiick!!! Where can I get some?
  2. NOW what!? <Broken axle shaft bolt>

    Just make it happen soilder, there is no backup, no reinforcemen. Its just you and this stud. Show him what you're made of. Take no prisoner's
  3. NOW what!? <Broken axle shaft bolt>

    I feel ya, I think I would try and use a Drexel and cut the nut off
  4. Price of Rubicon axles.

    I can get a brand new front axle from my parts guy for 2200, and that’s complete with locker axles, etc. the rear is like 1800 , but I already have a dana 44 in the rear
  5. Shredded Gears or broken Axle Shaft

    morris4x4. My goodness, what did they do to make the gears do that?
  6. NOW what!? <Broken axle shaft bolt>

    The way the flange is made it’s like a pressed stud, just like a lugnut, it it’s spinning I don’t see any other way of getting it off other than cutting the nut off.
  7. NOW what!? <Broken axle shaft bolt>

    Mine came out further than yours, I only had like 3 threads to go, didn’t realize it was bottomed out
  8. NOW what!? <Broken axle shaft bolt>

    I just worked with it,took all the other nuts off, pulled on the axle until the nut was flush with the housing and kept turning it, it finally came off
  9. NOW what!? <Broken axle shaft bolt>

    You can also grind halfway through the nut and wack it with a chisel
  10. NOW what!? <Broken axle shaft bolt>

    I had the exact same problem with the exact same nut. I put the stud under a bind . Just pulled the axle out and kept turning the nut and it finally came off. I welded the stud it so it would never do that again.
  11. HELP! 35s vs 37s, KM3 vs KO2? Falken? What should I do?

    I would do 35’s, just my cents worth.. I’ve already regeared for 35,s. You have 4.10? I would do 35,s this go around and do a gear change then run 37
  12. Dana 30 - Cross pin loose within carrier housing

    I did check mine when I was installing gears last week, it was fine. I'm at 8 months and 17,000 miles. That slop in the video has to cause serious noise . There is no way that thing is operating correctly. Maybe 37's on a dana 30 really messed up the locker and pin. And I'm just guessing, I...
  13. Dana 30 - Cross pin loose within carrier housing

    Absolutely, I had to knock mine in with hammer. There is certainly something wrong with the hole the crosspin goes through. Based on the movement of the locker, I would say it's messed up, and the carrier is trashed. Way too much movement
  14. Dana 30 inner pinion bearing PN help

    Thank you, but it won't be necessary. I got it installed!!!!!
  15. DIY Gear Swap - Step by Step Pic's - Rubicon 4.88

    Well, i have finished my gear swap. What a PITA. I want to thank chevymitchell who tolerated my stupid questions. I used Dana Spicer gear sets, 4.56 ratio. I was coming from 3.45 on 35 inch tires in a 2021 Jeep Wrangler Unlimited Sport. I have a Dana 30 front and a Dana 44 rear. The gears are...
  16. DIY Gear Swap - Step by Step Pic's - Rubicon 4.88

    Yea , I did that and the bearings on the carrier then installed the races in the differential. They cooled down for atleast 2 hours
  17. DIY Gear Swap - Step by Step Pic's - Rubicon 4.88

    I'm a moron, so excuse me
  18. DIY Gear Swap - Step by Step Pic's - Rubicon 4.88

    I did, it was a while before i put it in
  19. DIY Gear Swap - Step by Step Pic's - Rubicon 4.88

    I dont have a press, so I used Betty crocker and a freezer.
  20. DIY Gear Swap - Step by Step Pic's - Rubicon 4.88

    4.56 Dana spicer gears
Advertisement
Top