Mopar LEDs installed on JL Sport

[Joaozao]

What version of the firmware do you have? 11.0.7? I think that’s the one for the LED. TRYING TO FIND ONE IN utah

I still haven't updated it or installed it. Waiting until I get ready to install the headlights to update and install the tazer

Sponsored

 

[nag22]

Where did you buy the ?

Contact @EgGreg

 

[nag22]

What dealer did you go to?

I have a tazer but just in case

World Jeep in shrewsbury. If you need a hookup there send me a PM

 

[VillianJL]

Just installed a set of factory Mopar LED headlights on my JLU Sport !

Thanks to the help of @EgGreg !!! I am using one of his hand made harnesses which have a separate wire that runs off the harness to power the DRL. I ran that wiring to a Micro2 fuse tap adapter - which was ran to the power heated seat fuse.

All is well so far, the lights function properly so far. *** But tomorrow morning i am heading to a buddy at a dealer so that he can add the correct build code to my VIN and flash the computer so that there will not be any issues ! Fingers crossed for tomorrow. When i get home I’m going to fish some wire loom and clean up the wiring a bit.

Did you run both halo wires to one micro2 fuse tap?

 

[nag22]

Did you run both halo wires to one micro2 fuse tap?

yes

 

[zyt]

World Jeep in shrewsbury. If you need a hookup there send me a PM

You are so lucky to have a connection to someone works at the dealer. Do you know how long would it take for a flash to add Aux switches? my dealer charges a flat rate of 1hr labor, $150 for all flashes and adding it to the VIN.

 

[nag22]

You are so lucky to have a connection to someone works at the dealer. Do you know how long would it take for a flash to add Aux switches? my dealer charges a flat rate of 1hr labor, $150 for all flashes and adding it to the VIN.

I am really not sure, but the flash for the lights took less than 10 minutes

 

[JL.FR]

I am really not sure, but the flash for the lights took less than 10 minutes

Hello nag22, here in France I have a RUBICON, but the European LED headlights have only 3 pins and the connector too, so we do not have the halos ... outside are the same appearance as you, but I do not know if the halo is in or not. I dare to open the lighthouse to see if it is possible to add the pine 4. Then the connection is easy on the side markers or the park light. If you have an idea ???

 

[EgGreg]

Im willing to bet if you don’t have the 4th pin in the socket on the back of the headlight (not the connector plug that plugs into it) it doesn’t have halos

I made a pnp jumper for side light but it’s difficult to get to connector 3ft back behind the fender liner. It much easier (& less expensive) to use a fuse tap at the fuse box

 

[Kenny]

Installed today - off for the flash tomorrow -

 

[Kenny]

We ended up adding the following:
LBQ Exterior LED Lighting Capability
LNV LED Fog Lamps
LPX LED Reflector Headlamps

My lights work like new - want to thank Nag22 for all the help.

 

[nag22]

My lights work like new - want to thank Nag22 for all the help.

don't Thank me! It all started out with the help of @EgGreg!!!

 

[Mickgolf00]

don't Thank me! It all started out with the help of @EgGreg!!!

Great pics of all the connections. I agree. @EgGreg is the man! I ordered my assemblies a couple of days ago. Greg has the harnesses on the way. Can't wait to get theses things installed.

 

[Mickgolf00]

Funny thing. Went in for oil change/tire rotation. Asked to have the codes added to my VIN. First, it confused the tech. I went to this thread and pull the codes. He then came to me in a panic because...I guess...he tried to flash the vehicle. He found my mini-Tazer which I completely forgot to disconnect. He didn’t give me too hard of a time but sent me home with none of my lights working correctly. I promptly reconnected the Tazer and all things were good in the world again. My fault completely for not disconnecting but I was surprised he didn’t know what the Tazer does.

 

[Joaozao]

Funny thing. Went in for oil change/tire rotation. Asked to have the codes added to my VIN. First, it confused the tech. I went to this thread and pull the codes. He then came to me in a panic because...I guess...he tried to flash the vehicle. He found my mini-Tazer which I completely forgot to disconnect. He didn’t give me too hard of a time but sent me home with none of my lights working correctly. I promptly reconnected the Tazer and all things were good in the world again. My fault completely for not disconnecting but I was surprised he didn’t know what the Tazer does.

You can use the tazer to set the lights to LED and they will work perfectly

Sponsored