Sponsored

ARB air compressor mounting bracket

Globexradice

Well-Known Member
First Name
Mike
Joined
Dec 17, 2017
Threads
0
Messages
57
Reaction score
150
Location
Nj
Vehicle(s)
2012 jk
I have one more project I'm working on right now. As soon as that one is complete I can go back to this project.
Sponsored

 

BSw

Well-Known Member
First Name
Bert
Joined
Oct 22, 2017
Threads
17
Messages
186
Reaction score
195
Location
Sacramento, CA
Vehicle(s)
2018 JLUR - 2015 Ford Mustang - 2018 Volvo S90
I have one more project I'm working on right now. As soon as that one is complete I can go back to this project.
Any update on a timeline for a compressor mount?
 

Globexradice

Well-Known Member
First Name
Mike
Joined
Dec 17, 2017
Threads
0
Messages
57
Reaction score
150
Location
Nj
Vehicle(s)
2012 jk
working on it. I just finished my last prototype rear tailgate bracket and next week i'm working on the dual setup.
 

Globexradice

Well-Known Member
First Name
Mike
Joined
Dec 17, 2017
Threads
0
Messages
57
Reaction score
150
Location
Nj
Vehicle(s)
2012 jk
Here is that last pic I have of it. My final one has a camera mount built in. Then off to laser for production.

Dual arb bracket may take a little work before its production ready. Its tight under the hood but I did have it in there with room to spare.

20180614_132231.jpg
 

Sponsored

Schrodinger

Active Member
First Name
Adam
Joined
May 8, 2018
Threads
2
Messages
40
Reaction score
89
Location
Laguna Beach
Vehicle(s)
2018 Rubicon JL
Vehicle Showcase
1
I ended up mounting my single ARB on top of the spare tire carrier, slightly tucked inside the spare wheel.

Just drilled holes and mounted it.
34” before it gets wet... more than I’ll every do before water crossings.

FEEF71C0-3A9E-4874-B4AA-8745CB713035.jpeg
 
OP
OP
simpleJL

simpleJL

Well-Known Member
First Name
Kyle
Joined
Nov 29, 2017
Threads
75
Messages
1,457
Reaction score
2,467
Location
East Bay, CA
Vehicle(s)
'18 JLUR
Here is that last pic I have of it. My final one has a camera mount built in. Then off to laser for production.

Dual arb bracket may take a little work before its production ready. Its tight under the hood but I did have it in there with room to spare.

20180614_132231.jpg
Did you make a single ARB hood mount though?
 

Globexradice

Well-Known Member
First Name
Mike
Joined
Dec 17, 2017
Threads
0
Messages
57
Reaction score
150
Location
Nj
Vehicle(s)
2012 jk
Did you make a single ARB hood mount though?
I did but it only was made to fit the small. So if you arent running one just for lockers it's not going to work. The large was just a little to big to fit on that bracket
 
OP
OP
simpleJL

simpleJL

Well-Known Member
First Name
Kyle
Joined
Nov 29, 2017
Threads
75
Messages
1,457
Reaction score
2,467
Location
East Bay, CA
Vehicle(s)
'18 JLUR
Here is that last pic I have of it. My final one has a camera mount built in. Then off to laser for production.

Dual arb bracket may take a little work before its production ready. Its tight under the hood but I did have it in there with room to spare.
Where are you planning on putting the ARB twin?
 

Sponsored

tiltz

Well-Known Member
First Name
Dustin
Joined
Feb 8, 2018
Threads
8
Messages
51
Reaction score
29
Location
Washington
Vehicle(s)
Subaru STI
Here is that last pic I have of it. My final one has a camera mount built in. Then off to laser for production.

Dual arb bracket may take a little work before its production ready. Its tight under the hood but I did have it in there with room to spare.

20180614_132231.jpg
Ever get that dual compressor mount figured out?
 

Kansascoast

Well-Known Member
First Name
Jim
Joined
Nov 6, 2017
Threads
7
Messages
125
Reaction score
253
Location
Kansas
Vehicle(s)
Wrangler JKU, 2drJL
Ever get that dual compressor mount figured out?
Got it installed a couple months ago and it works great. I have had a few made for other forum members and so far the reports have been good. You can check it out at Goin2Drt build on this forum
Sponsored

 
 



Top