2021 Bright White JLUR Diesel build

[Kevin_S1126]

Beautiful Build @DrRay81. Have yo uhad a chance to install the VersaTable Yet? If so, how are you liking it and do yo uhave any video of how to run the wiring for the light? Thank you in advance

Sponsored

 

[DrRay81]

Finally got around to installing my versatable. Had to run a shorter bolt, which was included, in the spare tire carrier but still a hair too long so I cut it down again. Other Than that smooth install perfect fit

 

[DrRay81]

JCR lower front skid installed. Probably not functional at all but I can say it’s heavier duty Than the stock piece. More installed it because I really hated the look of the stock piece. Last install of the weekend will be the Oracle reverse lights. Summer Jeep wrenching is upon us. Undercloak system is next.

 

[DrRay81]

Got the Oracle reverse lights installed. Had to remove the spare tire and the rear bumper to install them. Fitment could be a lot better. The passenger side is snug fit and the screw hole was too shallow and snapped the screw off in the Oracle light. The fit is so tight I just left it as is. The driver side required grinding the light housing to get it to fit. Also a very snug fit. Wired them into the trailer hitch wiring so no taps. Once installed they look great and work great.

 

[Kevin_S1126]

Finally got around to installing my versatable. Had to run a shorter bolt, which was included, in the spare tire carrier but still a hair too long so I cut it down again. Other Than that smooth install perfect fit

Any video of how to run the lighting?

 

[DrRay81]

Any video of how to run the lighting?

It was pretty easy I ran it through the stock wiring loom(inside the nylon sleeve going from tailgate to the cargo area) then from passenger side to driver side through the weather stripping to the always on 12v wiring

 

[SlowPoke21]

I like what you have done. Very nice build sir.

 

[Steve949]

Took off the wrangler unlimited stickers and added some proper ecodiesel emblems.

Do you happen to have the part #? I'm not having any luck finding them.

 

[Steve949]

Beautiful build, by the way.

 

[DrRay81]

Do you happen to have the part #? I'm not having any luck finding them.

PART# 68359486AA

 

[Kevin_S1126]

It was pretty easy I ran it through the stock wiring loom(inside the nylon sleeve going from tailgate to the cargo area) then from passenger side to driver side through the weather stripping to the always on 12v wiring

thank you for the reply...much appreciated and your build looks phenomenal

 

[DrRay81]

AEV jack base installed. Saw a guy stranded on the side of the road with a flat tire and it got me thinking what if. So went ahead and ordered a jack base for that what if situation. Hopefully I’ll never need it

 

[DrRay81]

DCS rock light kit installed. 11 lights. One under the front and rear bumpers. One under each door on the frame rails. And one in each wheel well. And one mid mounted light

 

[Cjanak21]

Finally, after waiting what felt like forever after ordering(really was only 12.5 weeks) I took delivery on my 2021 Diesel rubicon 10/7. The order was a fully loaded rubicon msrp just under 65k. Just got the build more or less completed. Got the lift and suspension bits all done by the guys at Bull Run 4x4. Can't recommend them highly enough. Honest, professional, and really good at what they do.

The ATS stabilizer isn't a straight bolt in given the 2" Aluminum tie rod. on a stock car the ATS stabilizer bolts in just like factory, problem is that it still hangs low. the Doetsch tie rod and drag link kit you can add the stabilizer flip kit which includes a 2" clamp for the tie rod. problem is the through shaft stabilizer mounts with a different bracket but to the same OEM locations. so the guys over at Bull run fabbed and welded up a bracket so it is flipped higher above the tie rod. I'm leaving out all the little things like powder coating, tpms, and all the smaller details. but it rides fantastic could not be happier with how it turned out. And I know the jam nut on the drag link isn't torqued these were mid install pictures. haven't had a chance to take new ones, as I've been too busy driving the jeep.

I was averaging about 27.2 highway miles, with the 37's I'm getting 25-27 highway, 23-24city. next up are skids and diff covers. Huge thank you goes out to @BullRun4x4 and Travis@TriCityJeep

-3.5” Metalcloak gamechanger
-Accutune Fox Elite series DSC remote reservoir front and rear shocks
-Fox 2.0 Factory Series ATS Steering Stabilizer
-Synergy Manufacturing Front Track bar and Sector Shaft Brace
-Doetsch Off-Road 2" Aluminum tie rod and drag link
-Adams Front 1310 Extreme Duty Series Driveshaft
-Venom Rex VR501 17x9
-Nitto Ridge Grappler 37x12.5R17
-Rancho Rear LCA Skids
-Teraflex Alpha HD Tire carrier
-ZAutomotive JL Tazer Mini
-HotHead Headliner JL OEM Headliner Completion
-RedLine Tuning QuickLift Elite Hood struts
-Maximus 3 JL Classic Hoop
-Maximus 3 Dually Light Bracket
-Rigid Industries 360 series 6inch lights
-Artec Industries A-Pillar Dual Light Mount
-Rigid Industries D-Series Pro Spots
-Diode Dynamics clear sidemarkers
-Rau's Automotive Painted Dash Trim Bright White
-Metal Cloak Center Seat support
-Metal Cloak FAD skid
-Brawlee LED Tailgate light
-Bulletproof Driver and Passenger Single Phone mounts
-Mopar Rear Console Cupholder
-Mopar Cargo Tub Liner

Beautiful, giving me some great ideas for my ‘21 White JLUR…. Funny thing is I have the exact 501 VenomRex rims even b4 I saw this post, good taste!

Sponsored