35" and 37" JL pics with lift kit

[conFUcius]

Congrats on your upcoming lift! Rock Krawler is an incredible company that puts out real top shelf parts.

Top mounted drag links are only needed on lifts at least 4.5" and up. Bottom mount is perfectly fine for anything lower. SteerSmarts also has a great pair of brackets for relocating the steering stabilizer. 3rd pic is of the low profile bolt that attaches the stabilizer to the tie rod clamp, without interfering with the through shaft that passes over it when turning right.

Thanks for the advice/feedback!

Regards,

Young Grasshopper

Sponsored

 

[Fire Burns]

Yep, a $10 bolt...

 

[Hound Dog]

2021 JLUR 6-speed black - 2” Mopar, Nitto Ridge Grapplers 35x12.5 R17 on Fuel Blitz Black 17x9

What steps are on those rails?

 

[sanman357]

What steps are on those rails?

Looks like these.
https://mountainoffroad.com/products/hide-a-step-black-jl

 

[MDRubicon]

Looks like these.
https://mountainoffroad.com/products/hide-a-step-black-jl

Yes it’s the M.O.R.E hide-a-step... many people complain about the cost, however I don’t like the look of huge slider steps and power steps are too much $$$, so this to me was a nice compromise and I keep the rubicon rails as protection (win win).

It’s also nice because when you off-road you can just pull a pin and the steps come right off.

 

[LLRubylady]

2021 JLUR 6-speed black - 2” Mopar, Nitto Ridge Grapplers 35x12.5 R17 on Fuel Blitz Black 17x9

I had the 35 grapplers on my 6 spd but it felt sluggish. I am thinking about a regear. How do you find it?
Does it feel sluggish to you?

 

[MDRubicon]

I had the 35 grapplers on my 6 spd but it felt sluggish. I am thinking about a regear. How do you find it?
Does it feel sluggish to you?

Did you have a Rubicon with 4.10s?

I certainly notice a difference compared to stock, but it’s not too bad. I do plan to re-gear if I upgrade to 37s, however not to run 35s... I was on the fence about running K02 37s, which are actually more like 36s and lighter than the Nitto 35s; however, I wasn’t a huge fan of the BFG ATs when I had them in 33s on my TJ.

I’m also cool with not being fast/quick in the jeep, I’ll just take my time and enjoy the ride.

 

[OBJLU]

Correct... no longer going to regear/truss/chromoly.

The only tires that seem to measure true are the 40” Nitto’s and Mickey Thompson Baja Boss.

Have you actually measured the Baja boss mounted? I’m looking to buy a new set and can’t find any mounted measurements for those.
Thanks!

 

[MyThirdJeep]

2021 - 2” Mopar lift with 17x9 Fuel Covert wheels (+01) and 37x12.5 Nitto Ridge Grapplers

 

[VonteDoe]

Finally finished! Bottom pic is without lift. Sunset pic with lift. 2020. 2” mopar lift. 37’s cooper stt pro. 20” Fuels.

 

[T19]

2020 Rubicon
3.5 lift
20” wheels wrapped in 37” Toyo R/T

 

[JJsJL]

2020 Rubicon
3.5 lift
20” wheels wrapped in 37” Toyo R/T

Looks awesome!! Which fender DRL did you use? I really like the DRL mod when keeping the fender trim intact.

 

[Rangemaster]

2.5“ EVO stage 4 lift with 37” pats on beed locks.

 

[Kian]

2.5“ EVO stage 4 lift with 37” pats on beed locks.

looking into this same setup. How long did you have to wait for the entire kit? And how does it ride? Torn between these or the Fox 2.5 RR.. unfortunately if I go with the latter, I’d have to install an aftermarket driveshaft as per their instructions.

 

[Rangemaster]

looking into this same setup. How long did you have to wait for the entire kit? And how does it ride? Torn between these or the Fox 2.5 RR.. unfortunately if I go with the latter, I’d have to install an aftermarket driveshaft as per their instructions.

I had everything in a week. Bought the stage 4 lift, wheels and tires from northridge4x4 three weeks ago.

Sponsored